Contents Conformity certificates..........2 Troubleshooting............23 Introduction............... 2 Transportation, storage and disposal......25 Safety................6 Technical data............26 Operation..............10 Service..............28 Maintenance............14 Conformity certificates USA requirements delivery or written in the Engine manual. Take care of them as they are valuable documents. Labels are placed on the engine and/or in the To implement improvements, specifications and engine compartment stating that the machine will...
Page 3
Product overview Operator Presence Control (OPC) 1. Control levers 2. Parking brake The OPC engages when the operator lifts from the 3. Tracking control seat. The engine and the drive to the blades stop if 4. Deck lifting lever the blades are engaged or the parking brake is not 5.
Page 4
Product overview on page 3 for the position Refer to of the throttle control. Headlights PTO (Power Take-Off) button The PTO button engages and disengages the PTO clutch and the cutting deck or other equipment connected to it. The correct start conditions must be obeyed to engage the drive of the blades.
Page 5
Product overview on page 3 for engaged. Refer to the position of the hour meter. Always use approved hearing protection. Do not put your foot here. Neutral gear. Reverse gear. Each 50 hours an oil level symbol will show for 2 To do a check of the engine oil level hours.
yyyywwxxxx The rating plate shows serial number. yyyy is the production year and ww is the production Cold weather start. week. Note: Other symbols/decals on the product refer Cutting height low. to certification requirements for some commercial areas. Product damage Cutting height high.
Page 7
• Keep the product clean to make sure that you the exhaust system become very hot can clearly read signs and stickers. during operation. Risk of burn injuries, fire and damage to property or adjacent • Keep in mind that the operator will be held areas.
Page 8
Do a feel safe, do not cut it. check of the safety devices regularly. If the safety devices are damaged, speak to your Husqvarna • Remove stones, branches and other obstacles. service agent.
Page 9
• Use an approved transport vehicle for A spark arrestor for the muffler is available through transportation of the product. your approved Husqvarna dealer. • A markets national or local regulations can set limit to the transportation of the product.
• Keep the battery out of reach for children. product immediately serviced by a trained technician. • Charge the battery in a space with good airflow. • Keep flammable materials at a minimum clearance of 1 m when you charge the battery. WARNING: The exhaust fumes Disposal on...
Page 11
To adjust the seat • Do not move the control levers to the fully forward position or the fully reverse position 1. Lift the seat up and remove the seat adjustment during the initial operation. knob (A). • Learn how to operate the movement of the product on a hard surface, for example concrete 2.
Page 12
To disengage and engage the drive To set the cutting height system 1. Pull the cutting height lever in the direction of the seat. CAUTION: Only disengage or engage the drive system when the product is parked on level ground. If it is necessary to move the product by hand, with the engine off, the drive system must be disengaged.
Page 13
time. If the engine does not start, wait 15 3. Carefully push the 2 control levers forward. The seconds before you try again. product will start to move forward. The forward speed increases the more the 2 control levers c) When the engine starts, immediately release are pushed forward.
a) Pull the 2 control levers rearward in the 8. Remove the ignition key from the ignition when direction of the neutral position to decrease you are away from the product. the speed or stop the product. To get a good cutting result b) Move 1 control lever slightly forward and the other control lever slightly rearward to make a •...
Page 15
Daily maintenance Do maintenance Maintenance interval in hours Maintenance at a minimum of 1 Before After time each year Do a check of the safety system. Make sure that there are no fuel or oil leaks from the product. Make sure that there are no damage on the prod- uct.
Daily maintenance Do maintenance Maintenance interval in hours Maintenance at a minimum of 1 Before After time each year Clean the paper filter car- tridge. Examine the muffler and spark arrestor screen. Start the engine and blades and listen for un- usual sounds.
1. Connect one end of the red cable to the CAUTION: Do not use a high- POSITIVE battery terminal (+) on the weak pressure washer or a steam cleaner. battery (A). Water can go into bearings and electrical connections and cause corrosion which causes damage to the product.
To remove and install the front 2. Remove the bolt and the nut from the battery bracket and remove the battery bracket from the wheels battery. 1. Remove the nut and the bolt to remove the front wheels from the forks. 2.
Page 19
To adjust the parallelism of the 6. Turn the 2 outer blades to align with the cutting deck front to rear. cutting deck This procedure will set the cutting deck in a standard position. 1. Make sure that the tire pressure is correct. Refer Tire pressure on page 18 .
Page 20
Note: Technical data on page 26 from the pulleys. Refer to for the types of engine oil that Husqvarna 7. Remove the deck belt from the electric clutch on recommends. Do not mix different types of oil. the engine shaft.
Page 21
5. Install the oil drain tube (A) on the engine oil 11. Fill with new oil and do a check of the engine oil To do a check of the engine oil drain valve (B). level. Refer to level on page 20 . 12.
Page 22
Lubrication schedule Refer to Lubrication Interval Each 25 Each 50 Each 200 Daily hours hours hours Lubricate the grease nipple on the pivot axle with a grease gun. Do a check of the oil level. Replace the oil filter. To lubricate the front wheels Always use good quality grease.
Lubricate the joint bearing of the front wheels (B) with a grease gun until grease comes out. Troubleshooting Troubleshooting schedule If you cannot find a solution to your problems in this operator's manual, speak to your Husqvarna service agent. Problem Cause PTO (Power Take- Engine does not start.
Page 24
Problem Cause To examine the blades on page There is vibration in the product. The blades are loose. Refer to 19 . To exam- One or more of the blades are not balanced. Refer to ine the blades on page 19 . The engine is loose.
Do not discard the battery as domestic waste. sensitive rubber parts to become hard. Add stabilizer • Send the battery to a Husqvarna service agent to the fuel in the tank or in the container used for or discard it at a disposal location for used storage.
Technical data Technical data Z248F Engine Brand / Model Kawasaki/FR691V Nominal engine output, hp / kW 23.0 / 17.2 Displacement, cm Max. engine speed, rpm 3500 ± 100 Fuel, min. octane grade lead-free, max 10% Ethanol, max 15% MTBE Tank volume, gallons / l 3.5 / 13.25...
Page 27
Z248F Blade Engagement Electromagnetic Clutch Productivity, acres/h / m 2.5 / 10,117.1 Tires Tire pressure, rear – front, kPa / PSI / bar 103 / 15 / 1 Front caster tires, in. 11 × 6-5 Rear tires, turf pneumatic, in.
Service Service When you send an order for the spare parts, give information about the purchase year, model, type, Do a yearly check at an authorized service center to and serial number. make sure that the product functions safely and at Always use original spare parts.
Contenido Certificados de conformidad........30 Solución de problemas........... 52 Introducción............30 Transporte, almacenamiento y eliminación de residuos..............54 Seguridad..............34 Datos técnicos............56 Funcionamiento............39 Servicio..............58 Mantenimiento............43 Certificados de conformidad Requisitos para EE. UU. máquina en el momento de su entrega o que estén escritos en el manual del motor.
Page 31
Descripción general del producto Para hacer 1. Palancas de control atrás desde la posición neutra. Consulte funcionar el producto en la página 42 . 2. Freno de estacionamiento 3. Control de seguimiento Control de presencia del operador 4. Palanca elevadora del equipo (OPC) 5.
Page 32
Control de clima frío El control de clima frío se utiliza para arranques en frío a fin de suministrar más combustible al motor cuando la temperatura es inferior a 32 °F (0 °C). Presione el acelerador a la posición de clima frío cuando arranque un motor frío. Consulte Descripción general del producto en la página 31 para conocer la posición del acelerador.
Page 33
Fusibles La ubicación de los fusibles está en la caja de fusibles. La caja de fusibles está debajo del asiento. Use guantes protectores. Incline el asiento hacia delante para acceder a la caja de fusibles. Consulte la etiqueta de la caja de fusibles para identificar los diferentes fusibles.
Advertencia: El ácido de la batería es corrosivo, explosivo e inflamable. Mantenga las manos lejos de las piezas giratorias. Mantenga las partes del cuerpo alejadas de las piezas giratorias. Tenga cuidado con las personas y los animales cuando opere el producto aaaassxxxx La placa de característi- hacia delante.
Page 35
Instrucciones de seguridad relacionadas ADVERTENCIA: Este producto con los niños puede amputar manos y pies, y arrojar objetos. El incumplimiento de las ADVERTENCIA: siguientes instrucciones de seguridad atentamente las instrucciones de puede ocasionar daños graves o la advertencia siguientes antes de usar el muerte.
Page 36
pared u otra obstrucción. El material puede • Ponga atención a la presencia de surcos, rebotar hacia el operador. Detenga las cuchillas agujeros y baches, y no pase transversalmente cuando cruce por superficies de grava. por ellos. Existe un mayor riesgo de que el producto se vuelque en suelo que no es plano.
Page 37
Las palancas de control están en la posición las tierras federales. neutra. • El freno de estacionamiento está aplicado. Se puede obtener un apagachispas para el silenciador a través de su distribuidor Husqvarna • La transmisión de las cuchillas está desactivada. aprobado. • El OPC está presionado.
Page 38
Si la batería tiene antes de guardarlo. una deformación o está dañada, hable con un taller de servicio Husqvarna • Tenga especial cuidado al manipular gasolina y autorizado. otros combustibles. Estos son inflamables y los vapores son explosivos.
• La llave de encendido está en Si están equipados, desconecte los cables de las posición stop y retirada. bujías y el cable negativo de la batería antes de realizar cualquier reparación. • Las cuchillas están desacopladas. • Todas las piezas giratorias se han Para lograr mayores niveles de rendimiento detenido.
Page 40
• Asegúrese de que haya suficiente combustible 2. Afloje la perilla de ajuste del asiento (B). en el depósito de combustible. Ajuste de la • Ajuste la altura de corte. Consulte altura de corte en la página 41 . Para agregar combustible ADVERTENCIA: La gasolina es muy inflamable.
Page 41
Para desacoplar y acoplar el sistema • Para ajustar el producto en la posición de corte, ajuste la altura de corte apropiada. Consulte de transmisión Ajuste de la altura de corte en la página 41 . Ajuste de la altura de corte AVISO: Solo desacople o acople el sistema de transmisión cuando el...
Page 42
b) Empuje y gire la llave de encendido a la 2. Desacople el freno de estacionamiento. Consulte Para acoplar y desacoplar el freno de posición Start. estacionamiento en la página 40 . Tenga en cuenta: No mantenga 3. Empuje cuidadosamente las 2 palancas de la llave de encendido en la posición Start control hacia adelante.
b) Tire de la palanca de control derecha hacia 4. Coloque el equipo de corte en la posición de atrás en la dirección de la posición neutra transporte. para hacer que el producto gire a la derecha. 5. Mueva el acelerador hasta la posición de Mientras más tire de la palanca de control aceleración mínima.
Page 44
Programa de mantenimiento para el X = Las instrucciones se proporcionan en este manual de usuario. usuario O = Consulte el manual del motor para ver las instrucciones. Para llevar a cabo un Realice el mante- Intervalo de mantenimiento en ho- mantenimiento diario nimiento por lo Mantenimiento...
Page 45
Para llevar a cabo un Realice el mante- Intervalo de mantenimiento en ho- mantenimiento diario nimiento por lo Mantenimiento menos 1 vez al Antes Después año. Revise las correas y las poleas de la correa. Limpie el prefiltro de es- puma.
Page 46
Para cargar la batería • Use agua que corra de una manguera para limpiar el producto. No use presión alta. • Cargue la batería si está demasiado baja para • No apunte el agua a los componentes eléctricos Tiempos de carga arrancar el motor.
Page 47
2. Conecte el otro extremo del cable rojo al ADVERTENCIA: Ajuste siempre terminal POSITIVO (+) de la batería a la batería la velocidad de desplazamiento en un totalmente cargada (B). área abierta sin transeúntes. ADVERTENCIA: No haga 1. Revise la presión de los neumáticos. Consulte cortocircuitos en los extremos del Presión de los neumáticos en la página 47 .
Page 48
• Posición media: Césped de 2,5 a 4 in / de 64 a afiladas y pueden causar lesiones. Use guantes protectores. 102 mm • Posición inferior: Césped de 4 a 5 in / de 102 a 4. Mida la distancia entre el suelo y la parte inferior 127 mm de la punta de la cuchilla en el lado de descarga del equipo de corte.
Page 49
56 para ver los tipos de 1. Coloque la correa del equipo alrededor de la aceite del motor que Husqvarna recomienda. No polea del embrague eléctrico en el eje del motor. mezcle diferentes tipos de aceite.
Page 50
8. Cuando se haya drenado todo el aceite del ADVERTENCIA: No haga motor, gire la válvula de drenaje de aceite hacia funcionar el motor durante más de la derecha para cerrarla. Utilice una llave de 1-2 minutos antes de drenar el aceite 10 mm.
Page 51
Programa de lubricación AVISO: No utilice gasolina ni otros productos petrolíferos para limpiar las correas de transmisión. Consulte Lubricación Intervalo A dia- Cada Cada Cada 25 horas 50 horas 200 horas Lubrique la boquilla de engrase en el eje de pivote con una pistola de engrase. Compruebe el nivel de aceite.
Solución de problemas Programa de solución de problemas Si no encuentra una solución a sus problemas en este manual de usuario, consulte a su taller de servicio de Husqvarna. Problema Causa Botón de El motor no arranca.
Page 53
Problema Causa El motor no funciona correctamente. El carburador está mal ajustado. El filtro de combustible o el suministro de combustible están obstruidos. La palanca de acelerador está en la posición de arranque en clima frío. La válvula de comprobación en el tapón del depósito de com- bustible está...
Problema Causa La transmisión de las cuchillas no se ac- La correa de transmisión del equipo de corte está floja. ciona. El contacto del acoplamiento electromagnético está flojo. La transmisión de la cuchilla está dañada o suelta de los conec- tores de cable.
Page 55
No deseche la batería como un residuo ADVERTENCIA: doméstico. No mantenga el • Envíe la batería a un taller de servicio Husqvarna producto con combustible en el depósito o deséchela en un lugar para eliminación de en interiores o en lugares con mala baterías usadas.
Datos técnicos Datos técnicos Z248F Motor Marca / Modelo Kawasaki/FR691V Potencia normal del motor, hp / kW 23,0 / 17,2 Cilindrada, cm Máx. régimen del motor, rpm 3500 ± 100 Combustible, grado de octanos mínimo sin plomo, etanol al 10 % máx., 15 % MTBE máx.
Page 57
Z248F Acoplamiento de la cuchilla Embrague electromagnético Productividad, acres/h / m 2,5 / 10.117,1 Neumáticos Presión de los neumáticos, traseros y delanteros, 103 / 15 / 1 kPa / PSI / bar Neumáticos de la ruedecilla delantera, in 11 × 6-5 Neumáticos traseros, neumático para césped, in 18 × 9,5-8...
Servicio Servicio Cuando envíe un pedido de piezas de repuesto, dé información sobre el año de compra, modelo, tipo y Realice una comprobación anual en un centro de número de serie. servicios autorizado para asegurarse de que el Utilice siempre piezas de repuesto originales. producto funciona de forma segura y a su máximo potencial durante la temporada alta.
Page 59
Diagrama eléctrico 2241 - 001 - 11.08.2023...
Page 60
Original instructions Instrucciones originales 1142584-49 Rev. 2 2023-08-29...