Controls Description - Stiga ES 414 Series Operator's Manual

links the references in the text to the respective illus-
trations (listed on page iii and following pages).
1. COMPLETE ASSEMBLY
NOTE The machine can be supplied with some parts already
assembled.
WARNING! Unpacking and completing the assembly
should be done on a flat and stable surface, with enough
space for moving the machine and its packaging, always
making use of suitable equipment.
Disposal of the packaging should be done in accordance
with the local regulations in force.
1.1a Assembling the handle (Type"I" - without height
adjustment)
Attach the bottom part of the handle (1) to the side holes on
the chassis and fasten in place using the supplied screws (2)
as shown.
Assemble the top part (3) using the knobs (4) and supplied
screws.
Fit the cable fasteners (5) as shown and secure the control
cables.
Fit the starter cable in the guide spiral (6) and tighten the nut
(7).
1.1b Assembling the handle
(Type"II" - with height adjustment)
Return the bottom of the handle (1), already preassembled,
to the working position and secure it with the lower knobs (2).
Make sure the two pins (3) stay inside the respective holes (4).
Assemble the top part (5) using the knobs (6) and supplied
screws.
Fit the cable fasteners (7) as shown and secure the control
cables.
Fit the starter cable in the guide spiral (8) and tighten the
nut (9).
Loosen the knobs (2) to adjust the handle to two different
heights.
1.2a Assembling the grass catcher (Type"I")
Assemble the two parts of the grass catcher (1) and (2), mak-
ing sure the hooks are fully locked into place (3,4,5) and fasten
them using the supplied screws (6).
1.2b Assembling the grass catcher (Type"lI")
Insert the frame (15) in the fabric section of the grass catcher
(17) and snap on all the plastic sections (18), using a screw-
driver as illustrated.
Insert the outer edge (19) of the fabric completely into the
groove of the plastic part (13), starting 5 - 7 mm from the end.
1.3 Battery connection
• Electric key ignition models
Connect the battery cable to the general wiring connector
on the lawnmower.
• Electric push-button ignition models
Insert the supplied battery in the relative engine compart-
ment (par. 3.2b, "IV - "V").

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for a
throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
2.3 Drive lever (where applicable)
On power-driven models, pull the lever (1) towards the handle
for forward movement.
The lawnmower stops moving forward when the lever is re-
leased.
The engine must always be ignited with the drive disengaged.
WARNING!
sion, do not pull the machine backwards with the trans-
mission engaged.
2.4 Cutting height adjustment
The cutting height is adjusted by the levers (1).
On some models, remove the hub cover (2) and unscrew the
pin (3) with the provided wrench (4); fit the wheels into the hole
(5) that corresponds to the desired cutting height and fully
tighten the pin (3) with the wrench (4).
The four wheels must be adjusted to the same height.
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.
3. GRASS CUTTING
NOTE This machine can be used to mow lawns in a number of
different ways; before starting work, prepare the machine based
on how the lawn is to be mowed.
DO THIS WHEN THE ENGINE IS OFF.
3.1 Preparation for mowing and grass collection by
the grass catcher
Lift the rear discharge guard (1) and fasten the grass catcher
(2) correctly as shown in the illustration.
3.2 Engine ignition
During ignition, follow the instructions in the engine man-
ual.
3.2a
• Manual ignition models ("I - "II" - "III")
Pull the cutting means brake lever (1) against the handle
and firmly tug the knob on the ignition cable (2).
• Electric key ignition models
Pull the cutting means brake lever (1) against the handle
and turn the ignition key (3).
3.2b
• Electric push-button ignition models ("IV - "V")
– Insert the supplied battery in the relative engine com-
partment (4); (follow the instructions provided in the en-
gine manual).
– Insert the key as far as possible (if fitted) (5).
– Pull the engine cutting means brake lever towards the
handle (1).
NOTE Keep pulling the engine / cutting means brake or
the engine will stop.
EN - 4
To prevent damage to the transmis-