Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for RAEV BULLET X
- Page 1 BULLET X User Manual of Electric Bicycle...
-
Page 2: Table Of Contents
Contents 1.Basic Information 1.Basic Information 6.Battery ............02 ............02 ...................11 1.1 Unpacking Information ............02 1.1 Unpacking Information ............02 6.1 Precautions about Use of Lithium Battery .....11 6.2 Operating Environment .............11 1.2 Parts Description ..............03 1.2 Parts Description ..............03 6.3 Charging Environment ............12 2.Installation Procedure 2.Installation Procedure .........04... -
Page 3: Basic Information
1. Basic Information 1.1 Unpacking Information 1x Bicycle 1x Wheel 2x Pedal 1x Charger 2x Keys 1x Bicycle 1x Wheel 2x Pedal 5x Tools 1x User Manual 1x Charger 2x Keys 5x Tools User Manual 1x User Manual... -
Page 4: Parts Description
1.2 Parts Description LCD Display Handle Cushion Brake handlebar Car light Rear reflector Charging hole Switch Battery Front fork Controller Motor Tensioner Front Pedal Disc Brake... -
Page 5: Installation Procedure
2. Installation Procedure 2.1 Handlebar Installation Remove the pre-tightened set screws of the handlebar end cover using 4mm socket head wrench Place the handlebar, adjust it to a suitable angle, close the end cover of the handlebar and pre-tighten 4 screws using 4mm socket head wrench Tighten set screws of the handlebar end cover in the order of 1, 2, 3 and 4 90°... -
Page 6: Pedal Installation
2.3 Pedal Installation Differentiate the identifiers of left and right pedals, L means left pedal and R means right pedal When installing pedals, keep the pedal bolt end face vertical to the mounting hole of the crank and tighten and fix it using 15mm open spanner (When installing the left pedal, rotate it anticlockwise;... -
Page 7: Battery Installation And Removal
2.4 Battery Installation and Removal Inset the key, rotate it to ON state and place the battery in the body preset position; Forcibly push the battery downward to the bottom Rotate the key to Lock state and pull it out... -
Page 8: Battery Charging
3. Battery Charging Open the soft cover on the battery side Insert the plug of the charger into the charging port of the battery and connect the other plug to the power supply The status light of the charger is red After the battery is fully charged, the status light of the charger is green Remove the charger, keep it properly and close the soft cover If the battery is charged on board, please power off the instrument... -
Page 9: Riding Introduction
4.Riding Introduction 4.1 Riding mode In EV mode, press and hold ON. After power-off, adjust the gears (1-3) by Instrument ± Key, and pull the speed thumb shifter to enter EV mode In assistant mode, press and hold ON. After power-on, adjust the gears (1-3) by Instrument± Key, step on the pedal for more than half a cycle to enter assistant mode In manual riding mode-press and hold ON. -
Page 10: Introduction To Instrument Key Functions
4.2 Introduction to Instrument Key Functions ON/OFF: Press and hold ON for more than 2s to turn on the power; in startup state, press and hold ON for more than 2s to turn off the power M mode key: In startup state, the displayed information is switched among total distance (mileage/h), trip distance (mileage/h), riding time (h), total distance (mileage/h), maximum speed (mileage/h) and average speed (mileage/h) ±... -
Page 11: Precautions About Use
5. Precautions about Use 5.1 Compliance with Traffic Laws and Traffic Safety Tips 5.3 Preparation for Riding Do not refit the electric bicycle without permission; with maximum load of 150kg, the Check whether the power circuit and electric bicycle must not be overloaded the light are normal Do not lend the electric bicycle to people who cannot drive it to avoid injury Check whether the front and rear... -
Page 12: Battery
6. Battery 6.1 Precautions about Use of Lithium Battery Confirm battery model is original battery before use. Do not use batteries of other brands without permission Check whether the lithium battery is intact and has damage, leakage, heat emission, moisture, smoke and other obvious phenomena To ensure transportation safety, the battery quantity is about 30% upon delivery. -
Page 13: Charging Environment
6.3 Charging Environment Charge the battery using original charger instead of charger of other brands or models Please charge the battery at 0℃ -40℃ in a well-ventilated place and keep off combustibles Charging time: Do not charge the battery for more than 12h; otherwise, the battery life will be affected and a potential safety hazard will be caused Hazard will be caused;... -
Page 14: Technical Parameters
1 and constant speed of 12mph, on flat road surface, in a windless environment. Actual endurance mileage may differ with load, temperature, wind speed, road surface, operating habit and other factors. Product name Bullet X Net weight 36kg Product size... -
Page 15: Parameter Settings
8. Parameter settings When power is on, long press M (2 secs), to enter the parameter settings mode, you can edit the settings in this mode, long press M to exit this mode. *In this mode, if nothing is applied in 10 secs, the mode will be automatically exit. During riding (when the speed is above 0) this mode cannot be entered. The settings mode will automatically exit once start riding. - Page 16 Km/Mile: enter S7, press up/down to choose between km/h/MPH. Km/h Mile Backlit Lighting： enter bl, press up/down to choose between 1-5, 1 is the darkest, 5 is the brightest, default is 3. Auto OFF: enter OF, press up/down to choose between 0~15min. Default is 5min, 0 means auto OFF is off.
-
Page 17: Error Code And Faqs
Passcode: enter Pd, press M to switch, press up/down to change the number, default is “1919”, once the correct passcode is entered, it will enter the speed unlock settings. 0000 1919 Speed unlock: enter SL, press up/down to adjust, choose a number above20mile, the speed is unlocked. Km/h Km/h 9. -
Page 18: Error Code
9.1 Error code Individual special examples: Error code 21 The current is abnormal, the controller is malfunctioning, replace the controller. Error code 22 Throttle malfunction, unplug and reconnect the throttle cable. If the issue persists, replace the throttle. Error code 23/Error code 24 Motor malfunction, unplug and reconnect the motor cable, if the problem persists, replace the motor. -
Page 19: Faqs
9.2 FAQs Battery is turned on, but no power supply Check if the display is properly plugged The battery might be undercharged, charge the battery The power is turned on, but the motor doesn’t work when twisting the throttle Check if the brake lever is in the braking position Release the parking mode if it is in Gear 0 Insufficient mileage Check if the charger is damaged... - Page 20 Company: E-LINK TECHNOLOGY CO.,LTD Address: 4~5F/ B Block, Ding Bao Hong Green High-Tech ParkNo.8 Industrial2nd Road, ShiYan BaoAn District, Shenzhen, China. Email: support@raevbikes.com Website: raevbikes.com Made In PRC...