Ardi Technology SB11 User Manual

Multiple Wallet Reminder User Manual
1
1

Introduction

Introduction
The Wallet Reminder SB11 is a quick alarm to prevent your wallet
from lost. It can be easily put into any wallet since the size is half
of a credit card. Download the free HiProx Multi app from App
Store, and combine with Wallet Reminder unit, you will never lose
or leave your wallet behind. As a remote shutter release for
self-portraits or to prevent blur by shaking camera. Moreover, the
app will take a GPS snapshot when your wallet is away from your
phone for a certain range you set, which let you know where your
wallet is left at. This device works with your iPhone/iPad.
2

Specification

98 ft /30m (*Distance will vary depending on terrain and other factors.)
Search Range
Alert Range 7~30 feet / 2~9 meters adjustable
Battery Type CR2016x1
Battery Life 6 months
Weight 4.9g
Dimension 50x30x3mm(1.96x1.18x0.12inch)
Working Temperature Temperature: 5 ℃～40℃、 humidity: 20％～80％
3

Package components

A) Wallet Reminder Unit x 1~4
C) User Manual x 1
If any components are missing from the package, please return
the product to your dealer immediately.
4
3

Product description

Product Description
Front
Status LED
FindMe
Button
5

Quick setup guide

Quick Setup Guide
Step 1 - Download App "HiProx Multi"
Download "HiProx Multi" on App Store for free. (Please search
for HiProx Multi on App store, or search for and find the HiProx
Multi application)
Step 2 - Enable on your iPhone/iPad
Go to Setting General
Step 3 - Place battery into Wallet Reminder Units
Insert batteries in to Wallet Reminder unit in accordance with
the battery installation Instructions illustrated.
BE SURE TO SLIDE THE WALLET REMINDER UNIT
BATTERY BETWEEN THE UPPER AND LOWER BATTERY
CONTACTS.
IMPORTANT NOTE: Placing battery on top of contact and
closing the lid will cause damage to the battery terminal
and will invalidate the warranty.
1. Slide out the battery cover.(Figure 1)
2. Insert batteries (included) following the polarity markings
in the battery compartment
3. Close the battery cover back to its place as shown.
Notice : Once the battery is inserted, the power will
turn on automatically and enter pairing mode. Green
LED will blink per second to indicate device is ready
to pair.
B) Battery CR 2016 x 1~4
Back
Disable FindMe
Button Function
Hold Switch
Enable FindMe
Button Function
Battery cover
Enable
1
Step 4 - Run "HiProx Multi" application
a. Open "HiProx Multi"and tap the
upper right corner to discover all available devices.
b. "HiProx Multi" will pop up Pairing Request.
(Figure 3)
c. Select "Pair" from "Paring Request" for each device.
The Green LED light will blink once every 5 seconds in the
connecting mode.
d. Once the pairing process is completed, the iReminder
function is enabled.
1 2
Figure 2
5
6 7
8
9
10
11
12
13
14
Figure 5
Step 5 - Test the Wallet Reminder system
a. Set "Hold Switch" to "On" from Reminder to enable
Back picture)
"FindMe" function. (Please refer to
b. Press "FindMe" button on the Reminder unit , and your
device will beep.
c. Press and release "Find Me" button to stop the FindMe
function.
d. To set different alarm sounds for each tag, press 'Alarm Button'
(Figure 5)and go to Alarm Sound Selection View to choose your
alert tone for that tag.
e. Set alarm "threshold level" depends on the alarm distance
you
like.
Step: Range Alarm Threshold
bar depends on the distance alarm you need.
f. Test your setup by placing the iPhone in a stationary location.
Then take the Reminder and walk away from the device
when you reach 7-30 feet from the device, and your
device will beep. If you move back into the range, the alarm
will cease.
(Figure 7)
Page 1
CR2016
The side facing
upwards
2
Figure 1
button in the
4
Signal Indication
Figure 3 Figure 4
1. Enter Help menu
2. Find new device
3. Setting button
15
4. Signal indicator
5. Remove tag button
6. Change device name
7. Battery status
8. On/Off link loss function
9. On/Off range alarm function
10. Set alarm range
11. Alarm sound setting
12. On/Off Map location function
13. Enter Map view menu
14. Enter Camera function
15. Enter airplane mode setting
Figure 6
4 Product description
Move the threshold
(Figure 5)
7-30 Feet
Figure 7
(Figure 2)
3