Related Manuals for Systor SYS3 Series
Summary of Contents for Systor SYS3 Series
- Page 1 Systor SYS3 Series Hard Drive Duplicator User Manual Version 1.0 All rights reserved © 2017...
-
Page 2: Table Of Contents
Table of Contents Introduction Features Control Panel Overview Specifications Warning Operation Overview III. Menu Overview Copy Compare Copy + Compare Capacity Check Utility Format FAT32 Format exFAT Measure Speed Quick Erase Full Erase DOD Erase Change Disk Signatures Media Information Device Model 5.10 System Information... - Page 3 Button Beep Show Result Time Boot Password 6.10 Setup Password 6.11 Language 6.12 Clear Setup 6.13 Performance...
-
Page 4: Introduction
I. Introduction 1. Features Each processing channel has its own control unit and operates independently with • dedicated bandwidth of up to 300 MB/s, which is the fastest speed of HDD duplication on the market. Standalone operation. No PC or software is required, m inimizing possible computer •... -
Page 5: Specifications
3. Specifications Operation Standalone (No PC or software is required) 3.5” SATA HDD, 2.5” SATA HDD and SSD with optional adapter ( Supported HDD SATA I, II, III) Display 2-line Backlit Monochrome LCD 115V or 230V Power Supply Control Button 4 push-button control panel (ENT, ESC, UP, DOWN ) Working 20% ~ 80%... -
Page 6: Menu Overview
inserted after source HDD is plugged in. 2. The number of Ready device is increased on the LCD display if the target HDD is plugged in properly. 3. Select the task from menu, and press ENT button to execute it. 4. -
Page 7: Copy + Compare
3. Copy + Compare This command allows duplicator to start Copy process first and then follow with Compare process immediately. 3. Copy+Compare Copy& 7.8G &COMP 7.8G ： ： ： ： ： ： ： ： Ready device: 7 ： ： ： ： ：... -
Page 8: Measure Speed
[Utility] Sure to format? Format ： ： ： ： 1. Format exFAT E N T E N T E N T E N T E N T E N T E N T E N T ： ： ： ： ：... -
Page 9: Dod Erase
DoD Erase This option complies with the U.S.A. Department of Defense (DoD 5220) standard to fully erase the HDD by rewriting bit by bit three times to guarantee the data to be permanently deleted. This process takes the longest time to erase, and the content will not be retrieved by software. [Utility] Sure to erase? DoD Erase... -
Page 10: System Information
5.10 System Information This option displays general information of the duplicator, including controller model, system memory size, firmware version and number of targets. Controller Model Memory [Utility] H0202S 128MB Firmware Target Number 10. System Info. V1.06.00 E N T E N T E N T E N T Display system information... -
Page 11: Smaller Target
Smaller Target If the capacity of the target HDD is smaller than the source HDD, the duplicator will partly copy or cannot copy. Cannot Copy is the default setting. [Setup] [ [ [ [ S maller Target ] ] ] ] 3. -
Page 12: Start-Up Menu
Copy number of target ： ： ： ： Copy ： ： ： ： 2.5G 2.5G d ata to be copied ： ： ： ： 03:45 03:45 : copy time used r ate of progress ： ： ： ： Show Timer Mode A: 10 n umber of targets in copy process ：... -
Page 13: Boot Password
Boot Password This option allows the user to set up a password for system boot up to prevent from the unauthorized use of the duplicator. The password must be 6 characters. [Boot Password] [Setup] Boot Password 10. Boot Password Enable = = = >... -
Page 14: Performance
6.13 Performance This option allows the user to set up the performance for Copy function based on the following modes: Speed, Balance, and Compatibility. Speed mode is used to execute the Copy function at the fastest speed, but may have compatibility issue with certain brands of flash media. Balance mode is used to execute the Copy function at a stable speed, and has less compatibility issue with certain brands of flash media.
Need help?
Do you have a question about the SYS3 Series and is the answer not in the manual?
Questions and answers