Advertisement
Quick Links
FTDC-ADP-4CH Installation Sheet
As a professional, user-friendly and cost-effective dash camera
with built-in AI processor, Fleetly FTDC-ADP-4CH detects risky
driving events such as lane departure warning, forward collision
warning and headway monitoring warning, as well as unsafe
driving behaviors such as unfastened seatbelt, using mobile
phones, yawning, distraction and smoking.
Preface
This FTDC-ADP-4CH Solution Installation Guide is hereby prepared to better guide engineering personnel
to install FTDC-ADP-4CH and its accessories properly and quickly, and to improve installation efficiency.
This document mainly includes the following parts: preface, system overview, and preparation for
installation, introduction to installation, and acceptance and cleaning. This document is applicable to
installation engineering personnel.
Fleetly reserves the right of final interpretation of this document and the right to modify this document or
information and descriptions therein. The contents of the manual are subject to change without further
notice.
Important Notice
1. Before installation, please park the vehicle on the horizontal ground and shut down the engine (do
not park the vehicle on a ramp or an inclined road).
2. Please read the section of packing list carefully and check carefully at the time of unpacking.
3. Please read the section of tool list carefully and provide installation tools before product
installation.
4. Before installation, please observe the vehicle environment and follow the principles below:
a. The installation position and cabling of the product shall neither affect the driver's view nor
affect the adjustment of the rearview mirror and sun visor.
b. The lens for monitoring the road condition ahead of the vehicle must be within the working
range of the windshield wiper.
c. The installation position of the camera for monitoring the driver in the vehicle shall comply
with local regulations.
+91 888 666 0 661
+44 121 582 4700
FTDC-ADP-4CH
+1 (916)306-1113
www.fleetly.tech
AI Dashcam
Installation Sheet
hello@fleetly.tech
Advertisement
Summary of Contents for Fleetly FTDC-ADP-4CH
- Page 1 This document is applicable to installation engineering personnel. Fleetly reserves the right of final interpretation of this document and the right to modify this document or information and descriptions therein. The contents of the manual are subject to change without further notice.
-
Page 2: System Overview
1. System Overview 1.1 Product Overview FTDC-ADP-4CH is an AI dashcam that helps drivers to reduce traffic accidents and facilitates fleets to improve management efficiency. Based on AI technology, it can actively detect risky driving events and unsafe driving behaviours, supporting sending local real-time reminders to the driver to avoid risks and uploading events to the fleet management platform for driver training. - Page 3 Single-lens model 1.3 Schematic Diagram of System Connection-Power Supply through Standard Power Cable Dual-lens model Single-lens model +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
-
Page 4: Preparation For Installation
Confirmation of the above information is crucial. Installation can only be carried out after the above information is considered normal through confirmation. 2.4 Power Supply Connection of Vehicle FTDC-ADP-4CH has two power supply connection modes: 1. Quick power supply connection through the OBD port: This mode is suitable for quick installation by users. - Page 5 2.5 Connection of Necessary Signal Cables Where required, the following signal cables must also be connected to enable the intelligent assisted driving functions of FTDC-ADP-4CH: (1) CAN data cable - to obtain accurate vehicle speed (if GPS speed is used, the CAN cable may not be connected);...
- Page 6 List of Installation Tools and Accessories ssss Picture Tool Name Application Quantity Common screwdriver Tighten screws, optional 1pcs Crowbar Pry up the vehicle panel 1pcs Prepare Ties Bundle cables needed +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 7 Waterproof backfill after Waterproof sealant punching Waterproof protection for Waterproof tape outdoor wire connectors The following installation tools are also required for the installation of DMS camera if required: +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 8 To ensure normal online communication and data storage of the device, please prepare a supporting Micro SIM card and a Micro SD memory card that meets the quality requirements before installation. 4. FTDC-ADP-4CH Installation 4.1 Installation of SIM Card and Memory Card Take out the Dashcam (power-off), and use the Allen key in the kit to open the card slot panel on the right of the Dashcam by turning counter clockwise.
- Page 9 Micro SD card, it is required to use an industrial-grade Micro SD card, which can be used in a wide operating temperature range (-40℃ to 85℃) and has strong stability. Fleetly-recommended Micro SD cards are preferred. Failure to use the appropriate card as required may damage the accessories or even the device.
- Page 10 4.2 Selection of Dashcam Installation Area Requirements for installation area of FTDC-ADP-4CH: (1) The Dashcam must be installed in the middle of the front windshield. It is generally installed in the rear-view mirror area above the centreline of the front windshield. A deviation less than 5 cm on...
- Page 11 *Note: When installing the bracket, install the bracket according to the direction indicated on the bracket, so that the toothed side faces to the right. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 12 When fixing, ensure that the cockpit camera screen meets the following conditions: 1) The centre of the cockpit shall be in the middle of the screen. 2) The cockpit screen shall be horizontal. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 13 If the device is fixed and installed after power-on, it shall be powered on again before being tested or used. The GPS module built in FTDC-ADP-4CH is an inertial navigation module, and the above requirements can ensure the normal operation of inertial navigation products.
- Page 14 CAN-H and CAN-L cables generally correspond to pins 6 and 14, respectively. (The cable sequence varies with the shape of the OBD port. The example here is only for illustration.) +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 15 After the connection is completed, log in to the V yes app to connect the FTDC-ADP-4CH. Enter the configuration screen, and set the CAN model and baud rate of the device, and set the speed source as "OBD". At the same time, drive the vehicle for a short distance at the installation site to test the accuracy of vehicle speed pulse data.
- Page 16 (i.e., concealed cabling). +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 17 Since FTDC-ADP-4CH has a power supply box with a built-in turning-on/off control strategy, it is necessary to fix the power supply box at a certain position on the vehicle. Attention should be paid to the following items when the fixing position is selected: ①...
- Page 18 Enable Wi-Fi and GPS on your mobile phone before connecting the device with the truck Veyes App. After the FTDC-ADP-4CH is powered on, it remains in AP mode within 3 minutes by default. Then, run the truck Veyes app on your mobile phone and tap Search. The screen listing the Wi-Fi hotspots found is displayed.
- Page 19 Measure the vertical height (accurate to cm/inch) from the ground to the lens for road condition monitoring of FTDC-ADP-4CH with a tower ruler or tape and take it as the ADAS lens installation height. Measure the horizontal distance from the lens for road condition monitoring of FTDC-ADP-4CH to the outermost edge of the left tire (standing outside the vehicle and facing the left side of the front end) and take it as the left margin of the ADAS lens.
- Page 20 For manual calibration, there are two methods available, namely, the long-distance calibration method and the short-distance calibration method. However, since FTDC-ADP-4CH is capable of automatic calibration, it is only required to enter the relevant parameters manually in the manual calibration process, and it is not necessary to perform the long-distance and short-distance calibration procedures completely.
- Page 21 4. In the parameter input boxes, fill in the installation height of ADAS lens, the left margin of the ADAS lens, and the front-end width and front-end length read in 5.1.2 respectively. Refer to the +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 22 Tap Next to enter the screen as shown below. 5. Tap Next to enter the screen as shown below. Since FTDC-ADP-4CH is capable of automatic calibration, it is only required to tap Next directly without adjusting the device on this screen.
- Page 23 ADAS channel has returned to normal mode. At this point, the calibration operations of the FTDC-ADP-4CH from the preview screen are completed. 5.2 DSC Calibration (only for dual-lens FTDC-ADP-4CH) 5.2.1 Left and Right Rudder Setting...
- Page 24 6. Installation and Calibration of Optional Components 6.1 DMS Camera For different usage scenarios, three types of DMS cameras connected externally to FTDC-ADP-4CH can be selected at present: A-pillar side-mounted C29N, A-pillar side-glass-mounted C29N, and dashboard- mounted C29N.
- Page 25 4. Make sure that there is no other object (for example, the steering wheel) in the DMS video screen that will obstruct the driver's face and the seat belt features. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 26 Since the C29N comes with a G-sensor, it can automatically and flexibly adjust the horizontal and vertical changes of images to suit the installation states. Just check the image here. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 27 3. Adjust the left and right-angle joints of the DMS camera through the hexagon socket screws, so as to adjust the angle of the DMS camera left and right. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 28 If the vehicle has an airbag on the A-pillar, and the A-pillar side-mounted camera could not be mounted on the A-pillar, the camera with a glass mounting bracket can be chosen. The specific installation process is as follows: +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 29 (2) Make sure that the driver's face appears in the middle of the video screen, the driver's face and body are vertical on the video screen, and the lower edge of the screen is below the driver's chest. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 30 1. Tap Preview on the homepage to enter the preview screen. Double-tap the driver channel to enter the main stream full screen. 2. Tap AI Calibration for calibration selection. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 31 4. Select the corresponding channel of the DMS camera (select Channel 3 here). 5. Tap Calibration to move on to the next step. 6. Confirm the prompts - tap Next to move on to the next step. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 32 301 in the mode of side installation and side calibration (51 in the mode of front installation and front calibration), the calibration frame turns from red to blue, and then the calibration ends. Calibration is ongoing: +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 33 ADAS and DSC are successfully calibrated cannot be immediately seen. +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...
- Page 34 Take pictures of all the devices and the centre console after installation. (1) Take pictures of the installation positions of all items. (2) Take a picture of the rendering inside the cockpit after installation +91 888 666 0 661 +44 121 582 4700 +1 (916)306-1113 www.fleetly.tech hello@fleetly.tech...