Dear customer, thank you for choosing an Ibea product. In order to use at best this product, we advise you to read this manual in all its parts and keep it carefully for future reference. If you nd any anomalies or malfunctions, do not hesitate to contact Ibea assistance center closest to you.
Please read all safety warnings and instructions carefully. If the relevant warnings and instructions are not followed, electric shock, re and severe burns may occur. Do not use or expose electric trimmer in rain. When operating the electric trimmer, do not put your hands near the cutting area to avoid injury.
Product description This product is a battery driven electric pruning shears, which is composed of xed blade, mobile blade, lithium battery, charger, etc. It is mainly used for cutting and pruning grafting of fruit branches below 35 mm and pruning and harvesting of a large number of orchards.
Parts description 1. Moving blade 2. Fixed blade For 2 sec. appears 3. Pin total N. of cuts made, 4. Trigger later appears the N. of cuts 5. Display from beginning of session. 6. ON/OFF switch 7. Battery release button Battery charge level.
Disassemble & assemble the charging plug Supplied adapter. Push the charging plug inward in parallel with the socket of the charger to complete the installation. Press and hold the disassembly button as shown in Figure 1, and simultaneously push the charging plug outward.
Use and maintenance Instructions before use: 1. Please con rm the power of the battery pack before use. 2. When the trimmers are not in use, make sure that the trimmers and the power supply are disconnected. Please bear in mind that the power supply of the trimmers must be disconnected in the process of refueling, grinding blade and replacing blade.
Error reports In case of any fault, please handle it according to the prompt code on the disply screen. Fault prompt on the display screen: When using this product, if the following code appears on the screen, repair or handle it according to the corresponding fault prompt.
Battery Charging The battery of the new product is not fully charged. Place the battery on the desktop, insert the charger output jack into the battery socket, as illustrated in Fig. 1 and then plug the charger plug into the power socket. When the indicator light lights up, charging starts.
Page 11
Please use the charger included for charging, on which there is an indicator light corresponding to each charging plug (whether for individual charging or multiple charging, please refer to the indicator light on the charger to determine if charging is completed. The charger adopts a sequential charging method instead of simultaneous charging).
Precautions 1. It is normal for the charger and battery to heat slightly during charging. 2. If the battery is not used for a long time, it needs to be recharged every three months to prolong its service life. 3. A new battery or a battery that has not been used for a long time will not reach its maximum capacity before about ve times of charging and discharging.
18. Do not use any leaky battery. 19. Keep the battery away from children's reach. 20. Do not use or place the battery under the sun (or direct sunlight), other- wise it may cause the battery to overheat and catch re, which will result in functional failure and shortened life.
Blade replacement The power supply of the trimmers must be disconnected before operation. When the upper blade and the lower blade do not coincide well, or the blade is still not cut clean after grinding, it is recommended to replace the blade. The operation steps are as follows: 1.
11. Having reached 300,000 total cuts, the shears require extraordinary maintenance at an authorized Ibea service center, otherwise the warranty will be invalidated. Safety notes Warning! Please read all instructions carefully, not complying with instructions may lead...
Personal safety Use suitable clothing and protective shoes with non-slip soles. Use protective gloves. Use protective glasses. 1. Do not wear loose clothing or jewelry that could get caught in the parts in movement. 2. Maintain attention, do not get distracted, use common sense during use tool. Do not use the tool if excessively tired or under the e ect of drugs, drugs, alcohol or other substances.
Irregularity measures 1. In the event the pruning shear is not able to cut through an object, release trigger immediately, the moving blade will return to its open position automatically. 2. In the event the pruning shear is cutting through a particularly hard branch, release the trigger immediately, the moving blade will return to its open position automatically.
Warranty This machine has been conceived and manufactured through the most modern productive techniques. The manufacturer guarantees its products for a period of 24 months from the date of purchase except for professional continuous service products, used for work on behalf of third parties, for which the warranty is 12 months from purchase date.
Page 19
Of the machine: Name Battery electric pruner Linea Kratos Type Model Kratos 35 210001 From Serial number 07/2021 Date of construction Declares, under its own responsibility, that the above mentioned machine complies with the provisions of the following Directives and subsequent amendments:...