Related Manuals for O&M PF4000FH
Summary of Contents for O&M PF4000FH
- Page 1 O&M Manual Revision 4.1 PF4000FH PF4000FH utomatic Full height Turnstile Single or Double Duty Cycle: 100%...
-
Page 2: Introduction And Warnings
PF4000FH Introduction and Warnings This equipment is part of a large range of traffic flow products. They are designed to be easy to install, as all settings and internal wiring have been completed in our factory. Any of the instructions in this manual should only be carried out by a qualified service engineer or a competent person. - Page 3 PF4000FH Delivery, Movement & Transportation This article describes how your equipment will be delivered to you, specifications on the transportation used and advice including health & safety on movement of the equipment. The turnstile should ALWAYS! be moved with care and attention. The products are very heavy individually as well as a whole.
- Page 4 PF4000FH Guide to Physical Installation Component Identification and Notes: You should check that you have received the following in your order as they are referred to throughout this manual (note this can change per turnstile spec i.e. single components are different from double):...
-
Page 5: Notes Area
PF4000FH Guide to Physical Installation (cont) 60 5 45 mins 5/6. 7/8. Upright stansion Security screw Duct hole Front mounting plate Security screw Fixed rear plate Black boxes show fixing points from a “birds eye view” Directional Indicators 1 2 3... - Page 6 PF4000FH Header mechanism / Manual release guide This is a brief overview of the workings and location of parts on the header mechanism and how to set the turnstile in manual mode: 60 5 10 mins Header housing Manual rotate exit key Manual rotate entry key Directional LED’s...
- Page 7 PF4000FH PLC Usage Guide 60 5 10 mins Power Inputs Inputs I1 I2 I3 I4 IB I1 I2 I3 I4 IB Inputs I1...I4 IB..IE 24VDC 24VDC Inputs I1...I4 IB..IE 24VDC Analog or 24VDC 24VDC Analog or 24VDC Memory card slot...
- Page 8 PF4000FH Wiring Diagram (Illustration)
-
Page 9: Wiring Diagram (Schematic)
PF4000FH Wiring Diagram (Schematic) -
Page 10: Plc Inputs/Outputs
PF4000FH PLC and Electrical Guide PLC and Electrical Guide Overview picture of Internal Wiring (Note items/locations can vary depending on model/spec) PLC Controller Isolator Switch 24v Relay Phoenix Terminal Blocks Inverter Unit Fuse Holders Detailed Internal Wiring PLC Inputs/Outputs (Note items/locations can vary depending on model/spec) - Page 11 PF4000FH Mechanical Header Guide Mechanical Header Guide Overview picture Turnstile Header (Note items/locations can vary depending on model/spec) Header Shaft Limit Switches Limit Striker Solenoid Solenoid Paddle Levers Paddle Lever Adjusting Cams Ratchet Cog Guide Plates Spring Lever Bracket Header Shaft...
- Page 12 PF4000FH Operating the Turnstile First Operation Manoeuvres 1.Before attempting the steps outlined below please obey common sense and be aware that the turnstile will inhibit movement until commissioned so provide a diversion and inform site inc pedestrians. Follow the manual release guide in this manual and make sure the turnstile moves un-hindered by inserting the key and checking rotation in both directions.
- Page 13 PF4000FH Electrical Troubleshooting Guide The table (bottom) relates to the diagram directly below to help you trouble shoot electrical component errors Showing program in “run mode” Showing program in “Stop mode” I1 I2 I3 I4 IB I1 I2 I3 I4 IB...
-
Page 14: Troubleshooting Guide
PF4000FH Troubleshooting Guide WHAT IS THE PROBLEM? WHAT CAN BE THE REASON? WHAT CAN BE DONE? 1-It may be set out into "single 1-It is re-arranged from DIP- way free" mode. 2-Locking switcher into standard operating Turnstile allows authorisation to solenoid cable may be displaced or mode. - Page 15 PF4000FH Troubleshooting Guide WHAT IS THE PROBLEM? WHAT CAN BE THE REASON? WHAT CAN BE DONE? Although the power is supplied, 1-Power might not be received. 1-Power is supplied to the arms are not locked, indicators do 2-Internal power cable might be turnstile.
-
Page 16: Commissioning Certificate
PF4000FH Commissioning Certificate We certify that the system covered by this certificate has been commissioned satisfactorily. Contract Reference Completion Contract Title Engineers Installing Installation Commenced Commissioning Works Description Part/Whole Certificate Handover Date Part 3.The system(s) designed and installed in accordance with the following documents:... -
Page 17: Installation Checklist
PF4000FH Installation Check List System Operation - The user FULLY understands How to operate the system with all control devices How to isolate the power to the automation system How to manually release the system in event of power failure... -
Page 18: Service Log
PF4000FH Service Log This Manual must be completed in accordance with the guidelines below, at any point service/repair work is carried out on the product. This is to achieve two things; 1. To keep a history of the product for yourself and your supplier/manufacturer. -
Page 19: Certificate Of Conformity
PF4000FH Certificate of Conformity The machinery which this declaration refers to, is in accordance with the conditions of the following directives; Machinery Directive 98/37/CE. Low Voltage Directive 73/23/CEE. Electromagnetic Compatibility Directive 89/336/CEE. And is in conformity with the following standards & other specifications;... - Page 20 PF4000FH TECHNICAL DATA AND DIMENSIONS Dimensions: Rotor Spec: Type: Worm & Wheel Single: 1480mm x 1410mm x Overall speed: 9 rpm 2350mm Max rated torque: 440nm Double: 2220mm x 1500mm x Actual torque: 320nm 2350mm Gearbox efficiency: 55% Rotor: 76mm Ø tube with bottom...
Need help?
Do you have a question about the PF4000FH and is the answer not in the manual?
Questions and answers