Bosch 2 Series Quick Reference Manual

Bosch 2 Series Quick Reference Manual

Hide thumbs Also See for 2 Series:

Advertisement

Quick Links

en
Before using for the first time, read the instruction manual and the safety information it contains.
Short and handy...
... everything your dishwasher needs.

How to use your appliance

Load the tableware.
1.
Only clean tableware that is suitable for dish-
washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-

Overview of water hardness settings

You can find an overview of the water hardness values that can be
selected here.
A table of country-specific units can be found in the instruction
manual.
Hardness
mmol/l
Level
range
Soft
0 - 1.1
0
Medium
1.2 - 2.9
1
Hard
3.0 - 3.7
2
Hard
3.8 - 6.2
3

Adding special salt

To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.
Unscrew the lid of the dispenser for special salt
1.
and remove.
On initial start-up: Fill the dispenser right up with
2.
water.

Adding rinse aid

Press the catch on the lid
1.
of the dispenser for rinse
aid
and lift
⁠ .

Adding detergent

Add the detergent to the
1.
dry detergent dispenser.
tate freely.
Add detergent.
2.
Switch on the appliance
⁠ .
3.
Setting the water softening sys-
tem
Press
1.
To open the appliance settings,
2.
press
is flashing on the display.
a
LED A
LED B
LED C
Press
3.
water hardness has been set.
0, 1, 2 or 3 LEDs will light up ac-
cordingly.
To save the settings, press
4.
Add the special salt to the
3.
dispenser. The water in the
dispenser is displaced and
forced out. Never add de-
tergent.
Place the lid back on the dispenser and turn to
4.
close.
Add rinse aid up to the
2.
max mark.
2
1
Close the lid of the dispenser for rinse aid.
3.
a The lid clicks into position.
Close the lid of the deter-
2.
50 ml
gent dispenser.
25 ml
15 ml
a The lid clicks into position.
Select the programme.
4.
Start the programme
⁠ .
5.
Remove the tableware at the end of the pro-
6.
gramme.

Programmes

The programme data has been meas-
ured in the laboratory according to
⁠ .
European standard EN 60436.
The consumption figures depend on
for 3 seconds.
the programme and additional func-
tion selected.
repeatedly until the right
The runtime will change if the rinse
aid system is switched off or rinse aid
needs to be added.
Programme
for 3 seconds.
Intensive 70°
Auto 45-65°
Eco 50°
Express 65° - 1h

Machine Care

max
To cancel the programme, press
7.
approx. 4 seconds.
The programme is cancelled and ends after ap-
prox. 1 minute.
1) Duration [h:min]
2) Energy [kWh]
3) Water [l]
1) 2:10 - 2:15
2) 1,300 - 1,350
3) 11,0 - 13,5
1) 1:45 - 2:45
2) 0,850 - 1,350
3) 9,5 - 15,5
1) 4:30
2) 0,923
3) 10,5
1) 1:00
2) 1,100
3) 10,0
1) 2:10
2) 1,450
3) 15,0
for

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2 Series and is the answer not in the manual?

Questions and answers

Pam Holley
May 1, 2025

Had my dishwasher installed yesterday test run was ok .Now fully loaded and can not get it to go

1 comments:
Mr. Anderson
May 16, 2025

The Bosch 2 Series dishwasher may not start when fully loaded due to the following reasons:

1. The supply hose is kinked. ▶ Install the supply hose without kinks.
2. The water tap is turned off or jammed. ▶ Turn on the water tap or check for blockage.
3. The wastewater hose is kinked or blocked. ▶ Reposition or clear the hose.
4. The siphon connection is sealed. ▶ Check and open the siphon connection.
5. The cover of the wastewater pump is loose. ▶ Secure the cover until it clicks into place.

These issues can prevent the dishwasher from filling or draining properly, stopping it from starting.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Bosch 2 Series

  • Page 1 Before using for the first time, read the instruction manual and the safety information it contains. Short and handy... Overview of water hardness settings Setting the water softening sys- Programmes ... everything your dishwasher needs. You can find an overview of the water hardness values that can be The programme data has been meas- selected here.
  • Page 2 Cleaning filters Cleaning spray arms Clean wastewater pump After each wash check the filters for Press the locking Unscrew the upper spray arm Disconnect the appliance from the power supply. residue. catches pull down to remove ⁠ . Remove the filter system. Turn the coarse gether and lift Scoop out any water.

This manual is also suitable for:

Sgs2itw08g/01

Table of Contents