Dear Valued Customer, The device you have bought is manufactured by taking quality as priority and designed in order to provide you the best performance. We advise you to read the explanations offered in this guide carefully and to act in accordance with the stated rules before installation of the device and before using the device in order to ensure the best performance.
Please examine the general view of • Observe applicable safety the device on Image A instructions in your region. Sliding glass lid • Use only the original spare parts provided by the manufacturer in order Separator to maintain the safety conditions. Handle 4.
2 – SAFETY INFORMATION AND ENVIRONMENTAL SUGGESTION WARNINGS In order for the equipment to be used in the most efficient 2.1 – BEFORE OPERATION OF way, the ambient temperature THE EQUIPMENT where it is located must be important considered. The ambient accordance with the aspects stated temperature in the area where below...
where the equipment is located, NOTE keep your equipment away from such sources. Otherwise, fire, explosion, etc. The internal part of the may be experienced. equipment must be dry before • Plug equipment placing products inside. ventilate the environment where the equipment is located.
environments to provide Climate Class 3 (25°C– 60% R.H.). 2.4 – WASTE DISPOSAL WARNING This equipment is compatible with EXPLOSION HAZARD Waste Electrical Electronic Never use electrical Equipment (WEEE) Control appliances inside the Regulations.Within the scope of this equipment. regulation, it may be recycled by Licensed Companies disposed of under conditions consonant...
3 – INSTALLATION SUGGESTION 3.1 – SELECTION OF DEVICE Comply with the Authorized PLACE Persons guidance and The working environment is very suggestions for place selection significant in order for the device in order to get the best to work smoothly. Ensure that the performance from the device.
3.3.2– MULTIPLE DEVICE USE LAY-OUT POSITIONS 3.3.2.1– STAND ALONE USE Pay attention that there is at NOTE least 150 mm distance between the Packaging materials may wall and the device (back part). The be dangerous for children. device may have a contact with the Preserve the packaging wall on the side.
3.3.2.4– HEAD FRIDGE AND • Extension cables or multi-plugs shall not be used. ISLAND ARRAY • Damaged electric cable shall be It is the island group consisting replaced by a professional electricity of head fridges, which are placed expert. at the head of the group, in addition to the back-to-back array.
4 – DEVICE USAGE 4.1 – THERMOSTAT ADJUSTMENTS (EWPLUS 978) 4.1.1– GENERAL INFORMATION AND INSTRUCTIONS The explanations regarding the symbols on the thermostat and general information about the settings are given below. NOTE When the device starts working, check whether screen and light are working or not.
Page 14
Reduced SET / Economy LED Fans LED Permanently on: Energy Permanently on: Fans active Off: Otherwise Saving active Flashing: Reduced set active Quick flashing: Access to level2 parameters Off: Otherwise Compressor LED Defrost LED Permanently on: Compressor Permanently on: Defrost active active Flashing: Delay, protection or...
You may change the mode according to the instructions below: • Press the key [ ] for 5 seconds while the equipment runs. You will see the word “OFF” on the screen and the equipment will turn off all functions except of lighting.
Cooler Mode: 12 Hours Freezer Mode: 24 Hours Et(Meat)Modu: 12 Hours 4.1.4– MANUAL DEFROST Hold down the [ ]key for longer than 5 seconds. It is only activated if the temperature conditions are fulfilled. Otherwise, the display will blink 3 times to indicate that the operation will not be performed.
Reduced SET / Economy LED Fans LED Permanently on: Energy Permanently on: Fans active Off: Otherwise Saving active Flashing: Reduced set active Quick flashing: Access to level2 parameters Off: Otherwise Alarms LED Compressor LED Permanently on: alarm active Permanently on: Compressor Flashing: alarm acknowledged active Off: otherwise...
4.3 – THERMOSTAT uppermost or lowermost button to scan ADJUSTMENTS (AKCC 210) the rolling stack. 4.3.1–GENERAL INFORMATION 4.4 – THERMOSTAT AND INSTRUCTIONS ADJUSTMENTS (ERC 112D) Thermostat visual is presented on 4.4.1–GENERAL INFORMATION Image H2 AND INSTRUCTIONS Keys; explanations regarding 1-Short press, acknowledge alarms symbols on the thermostat and general or see control status.
4.5 – THERMOSTAT ADJUSTMENTS (CRA) 4.5.1–GENERAL INFORMATION AND INSTRUCTIONS The explanations regarding the sybols on the thermostat and general informtion about the settings are given below. Thermostat visual is presented on Image 1) [ ] - Displays the control setpoint. Exit the control setpoint and save the changes.
5 – SPECIAL INSTRUCTIONS FOR USE Perform the external cleaning of your equipment with cotton cloth and warm water. Prevent the cleaning water from penetrating into the lighting parts of the equipment during cleaning. • Clean the cover seal only by using clean soapy water. The plastic components of your equipment might get damaged due to cleaning with chemical cleaners (such as thinner, etc.).
5.4 – LOADING CAPACITY WARNING • Make sure that the foods loaded in the equipment are below the loading ELECTRIC SHOCK line (Image I Never wash this equipment. • Do not place products in the equipment before reaching sufficient storage coolness. 5.3 ...
6.2 – CARRYING THE DEVICE 6 – TURNING OFF AND CARRYING THE DEVICE Empty the foods out of the device, dry the interior part of the device 6.1 – TURNING OFF THE DEVICE properly and leave the lid open. If will not use the equipment for •...
7 – TURNING OFF AND CARRYING THE DEVICE In case you encounter the problems stated below, please check whether you can solve the problem by yourself or not before contacting the Authorized People. In case the problem exceeds your boundaries of authority, please call the Authorized people.
Page 24
Internal lightning is not Get in contact with the LED is malfunctioned working. Authorized Person. The stays of the device Control the accuracy of the operation of 3.3.1 (Image C are not balanced. Device is in contact with Disconnect the device from the Device is making too another object.
Page 25
NOTE The device will make some sounds while working. These sounds may be normal. Check the table below. Device Operating Sounds Humming sound Cooler system is working. Babbling, rustling sounds Cooling gas is passing through pipes. Compressor is being activated and Clicking deactivated.
Need help?
Do you have a question about the SFI Series and is the answer not in the manual?
Questions and answers