VERIFIER TRAILER INSPECTION SYSTEM USER GUIDE The future of trailer testing offered by LITE-CHECK Doc#: 87008, Revision date: 2018-08-27 U.S. Patent No. 8,571,751. Spokane, WA. U.S. (2015). U.S. Patent No. 8,751,099. Spokane, WA. U.S. (2015). U.S. Patent No. 8,855,853. Spokane, WA. U.S. (2015).
Securely stores inspection reports received from the tablet, allowing them to be viewed, printed, or saved from any smart device with internet access. The Lite-Check VERIFIER Trailer Inspection System is the culmination of 25 years of providing industry-leading trailer diagnostics designed to increase inspection reliability and reduce time and cost per inspection while increasing both trailer availability and road readiness.
Attach the tester power cord directly to a 12-volt battery or a regulated power supply. If the VERIFIER 1020 does not turn on and the power source is good, check for reversed polarity of the power cable.
Remember: Power to the tester must be regulated to protect the trailerʼs ABS electronics and ensure consistent tester performance. Power Warning: The Lite-Check VERIFIER Trailer Interface monitors the current flow through the ground circuit to aid in identifying various fault conditions. Care should be taken to ensure that the Trailer Interfaceʼs power source is not grounded to the trailer being tested.
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM System Component Descriptions VERIFIER Trailer Interface: Microprocessor controlled high-precision machine used to connect to electric, air and ABS systems of semi-trailers. VERIFIER Tablet: Used to guide the technician through the inspec- tion process and remotely operate the VERIFIER Trailer Interface.
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM Trailer Interface Overview The Lite-Check VERIFIER Trailer Interface has the following components: Feature Function Bluetooth Antenna For communication with Tablet USB Port (Internal) For updating the Trailer Interface firmware Turns Trailer Interface on and off...
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM VERIFIER Trailer Interface and Tablet Setup The following steps should be taken to ensure proper setup of the Lite-Check VERIFIER Trailer Interface. 1. Mount the unit securely 2. Connect the incoming air supply with at least 120 PSI from the compressor through a filtered air regulator set to NO LESS than 120 PSI 3.
Performing an Inspection 1. On the tablet, start the Lite-Check DOT app by pressing its icon on the home screen. 2. Enter your credentials and tap ”OK” to login. After a few moments you should see the tester voltage in the upper left corner of the screen.
Page 10
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM 10. Tap ”Save” to proceed, then press the ”Run Tests” button to begin automated testing of all light circuits and the ABS system. The ”info” button for each test can be selected to see results in real time.
OOS items, including notes and pictures if any. You may tap ”Submit” to send the report to the Lite-Check Cloud for secure storage, reporting, analytics, viewing, and printing, or tap ”Modify” to go back and repeat tests or modify selections and entered values...
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM Bluetooth Tire Tool (Accessory) The Bluetooth tire pressure and tread depth tool should be paired with the tablet when you receive it. Hold the button down until the LED illuminates to power the tool on. The first time you use the tool, press the Bluetooth icon in the DOT application and select the ”Trans-Logik”...
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM Tablet Diagnostic Mode Features The image and notes below reference the diagnostic mode of the Lite-Check DOT app found on the Lite-Check supplied tablet. Touching the indicated ”buttons” will activate the desired function. Switch to Inspection Mode Tester Input Voltage NOTE: Only ”lit”...
5. Return to Air functions to perform the ”LEAK” test for Emergency, or Emergency and Service 6. To submit the gathered data to the Lite-Check Cloud for storage, viewing, or printing, select Submit Report from the menu Provides real-time air pressure on both Emergency and Service air systems Allows for testing of just Emergency or Emergency and Service circuits Leak rates are displayed during the Air Leak Test.
Reads Haldex, Bendix, Meritor and Wabash ECUs with PLC through the AUXILIARY PIN 7 (with some exceptions–contact Lite-Check for details) Includes support for Roll Stability and Advanced ABS Displays all PLC ABS information on the Tablet screen for easy access Steps of ABS operation 1.
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM Lite-Check Cloud The Lite-Check Cloud serves as a secure repository for all inspection reports submitted from the tablet. From the cloud you can view all inspection reports, see the inspection history of a trailer, view fleet status, perform analytics and more.
B. Swipe the title bar of the DOT app off the screen C. Return to Home screen D. Press the ”LITE-CHECK DOT” icon on the Home screen to restart E. If these steps do not resolve the problem, move on to step #3 3.
Please enter as much information as possible about what you were doing prior to the crash and any other details that may help us find the problem and then send the e-mail (the Lite-Check Verifier tech-support e-mail address is automatically set as the destination). If Wi-Fi with internet access is not...
LITE-CHECK products have a one-year limited warranty on parts and labor against manufacturing defects. All warranty service to be performed at LITE-CHECK, Spokane, Washington. The Customer is responsible for shipping costs. The warranty does not cover abuse, neglect, or damage caused by air, electrical, or other outside sources as specified in the ownerʼs manual.
LITE-CHECK VERIFIER TRAILER INSPECTION SYSTEM Shipping LITE-CHECK Products Please follow these instructions for shipping LITE-CHECK testers and products to minimize damage. 1. Call lite-check to get an RMA (Return Merchandise Authorization) 2. Remove all air connections from the tester 3. Include the tablet and tire tool (if applicable) 4.