Advertisement
Quick Links
Introduction
Purpose
This manual provides instructions for installing Orpak
Kit and Cover (M09680B136).
Verify that the cabinet/pedestal is disconnected from power supply during the course of
the procedure.
Intended Users
This manual is intended for Gasboy
(ASCs).
Table of Contents
Topic
Introduction
Important Safety Information
Installing OrPT Barcode Kit and Cover
Required Tools
To install the OrPT Barcode Kit and cover, you require a screwdriver.
Parts List
Following table lists the parts included in the OrPT Barcode Kit:
Item Description
1
2
3
4
5
6
MDE-5262A Barcode Reader Installation and Setup Instructions · May 2016
WARNING
Barcode Reader, Hand Held Products (HHP)
Card Reader Cover, OrPT Panel
Barcode Holder, OrPT Panel
Nut, M3
Screw, M3 X 8 (including Spring and Flat Washer) 815225200
Harness Barcode Reader, OrPT
Installation and Setup Instructions
's Payment Terminal (OrPT) Barcode
™
-trained and certified Authorized Service Contractors
®
Page
1
3
5
Orpak Part
Number
813113200
814941200
814941400
815102500
819122525
Barcode Reader
May 2016
Quantity
1
1
1
2
4
1
MDE-5262A
Page 1
Advertisement
Summary of Contents for Gasboy Orpak M09680B136
- Page 1 Kit and Cover (M09680B136). WARNING Verify that the cabinet/pedestal is disconnected from power supply during the course of the procedure. Intended Users This manual is intended for Gasboy -trained and certified Authorized Service Contractors ® (ASCs). Table of Contents Topic...
-
Page 2: Related Documents
Introduction Related Documents Document Number Title GOLD Library MDE-4819 OrPT Gasboy’s Payment Terminal INSTALLATION, SETUP AND Gasboy OPERATION MANUAL FOR HOME-BASE STATIONS PT-1963 Gasboy Fleet Plus Illustrated Spare Parts Manual Gasboy Fleet PLUS systems Abbreviations and Acronyms Term Description Authorized Service Contractor... -
Page 3: Important Safety Information
Replacement Parts procedures should install, inspect, maintain or service this Use only genuine Gasboy replacement parts and retrofit kits on equipment. your pump/dispenser. Using parts other than genuine Gasboy replacement parts could create a safety hazard and violate Emergency Total Electrical Shut-Off local regulations. - Page 4 Important Safety Information No Open Fire In an Emergency Inform Emergency Personnel Compile the following information and inform emergency Open flames from matches, lighters, welding torches personnel: • Location of accident (for example, address, front/back of or other sources can ignite fuels and their vapors. building, and so on) No Sparks - No Smoking •...
- Page 5 Installing OrPT Barcode Kit and Cover Installing OrPT Barcode Kit and Cover To install the OrPT Barcode Kit and cover, proceed as follows: Turn-off the AC Power to the Islander PLUS unit. ™ Unlock and open the Islander PLUS door assembly. Remove all cable connectors.
- Page 6 Installing OrPT Barcode Kit and Cover Peel off the label that covers the barcode reader pane on the rear side of the OrPT front panel, by carefully inserting a screwdriver between the label and the OrPT frame in order to lift the label, and then peel it off with your hand, as shown in Figure CAUTION...
- Page 7 Installing OrPT Barcode Kit and Cover Place the barcode reader with the bracket on the terminal and secure it with two M3 screws (see Figure Figure 4: Securing Barcode Reader to Terminal Connect the barcode reader to the OrPT using the provided harness as shown in Figure Figure 5: Connecting Barcode Reader to Terminal MDE-5262A Barcode Reader Installation and Setup Instructions ·...
- Page 8 Installing OrPT Barcode Kit and Cover Replace the flat cover with the profound barcode/card reader cover provided in the kit (see Figure Figure 6: Replacing Bottom Rear Cover Ensure all connections are correct before closing the panel. Place the rear panels on the terminal and secure them using the seven M3 screws removed in step 6 page 5 (see...
- Page 9 Installing OrPT Barcode Kit and Cover Setting Up Fleet Head Office (FHO) For FHO setup, proceed as follows: Browse to FHO application and click Setup. Note: This feature is available from version 6.4.47.010. In the General tab, click Setup for customizing OPT messages. The prompts customization dialog box appears.
- Page 10 Installing OrPT Barcode Kit and Cover In the Screen state drop-down menu, choose the prompts for which the barcode should be activated (i.e. “Enter device ID”, “Enter Driver ID”, “Enter Vehicle ID”, and so on). Figure 9: Screen and Prompts Customization Check the Bar code reader checkbox in the Prompt Settings section at the bottom of the dialog box.
- Page 11 Installing OrPT Barcode Kit and Cover Repeat steps through page 10 for all the prompts for which the barcode should be activated (i.e. “Enter device ID”, “Enter Driver ID”, “Enter Vehicle ID”, and so on, as shown Figure 9 page 10).
- Page 12 FuelOmat is a trademark of Orpak Systems Ltd. Gasboy is a registered trademark of Gasboy International. Gilbarco is a registered ™ ® ® trademark of Gilbarco Inc. GOLD is a service mark of Gilbarco Inc. Internet Explorer is a registered trademark of Microsoft ®...