Table of Contents
Summary of Contents for ZKTeco V4L
- Page 1 Quick Start Guide 4-inch Thermal Imaging Product Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
- Page 2 Overview Thermal Imaging Temperature Detection Module Flash Near-infrared Flash Camera & Palm Collector Microphone Speaker 4-inch Touchscreen Reset Doorbell Button Card Reading Area Alarm Auxiliary Power In Input Lock Exit Button Sensor 485B BELL+ Bell RS485 485A BELL- Ethernet IWD0 WiegandIn IWD1 +12V...
-
Page 3: Installation Environment
Installation Environment Please refer to the following recommendations for installation. INSTALL INDOORS AVOID INSTALLATION AVOID DIRECT AVOID USE OF ANY ONLY NEAR SUNLIGHT HEAT SOURCE GLASS WINDOWS AND EXPOSURE NEAR THE DEVICE Recommended Palm Gestures KEEP EFFECTIVE KEEP SPACES DO NOT KEEP DO NOT KEEP DO NOT KEEP DISTANCE OF... -
Page 4: Installation Requirements
Installation Requirements The installation requirements and indications associated with the device are given below: Specification Standard value Remark Indoor, Avoid wind, Avoid The recommended operating Operating direct sunlight, temperature is 25°C (77°F) Environment 16°C to 35°C (60.8°F to 95°F) Distance The recommended distance 30cm to 120cm (0.98ft to 3.94ft) (between face... -
Page 5: Standalone Installation
Standalone Installation Alarm Smoke Detector Door Sensor Exit Button Card ZKBioAccess IVS Lock TCP/IP Reader Power Connection 12V DC Recommended AС Adapter 1) 12V ± 10%, at least 3000mA. 2) To share the power with other devices, use an AС Adapter with higher current ratings. -
Page 6: Ethernet Connection
Ethernet Connection ZKBioAccess IVS RJ 45 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 Click [COMM.] > [Ethernet] > [IP Address] , input the IP address and click [OK]. Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment when connecting to ZKBioAccess IVS software. -
Page 7: Lock Relay Connection
Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (normally opened when powered) is connected with 'NO1' and 'COM' terminals, and the NC Lock (normally closed when powered) is connected with 'NC1' and 'COM' terminals. The power can be shared with the lock or can be used separately for the lock, as shown in the example with NC Lock below: 1) Device not sharing power with the lock +12V... - Page 8 Wiegand Reader Connection Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last two pins are used by the Access Controller, as shown in the following figure. It sends the credentials to the device via wiegand communication. Access Controller IWD0 IWD1...
-
Page 9: User Registration
User Registration When there s no super administrator set in the device, click on enter the menu. Add a new user and set User Role to Super Admin, then the system will request for administrator’s verification before entering the menu. It is recommended to register a super administrator initially for security purposes. - Page 10 Method 2: Register on ZKBioAccess IVS software Please set the IP address and cloud service server address in the Comm. Menu option on the device. Click [Access] > [Access Device] > [Device] > [Search] to search the device on the software.
- Page 11 Method 3: Register on the phone Once the ZKBioAccess IVS software is installed, the users could enroll their face via a browser application on their own mobile phone. 1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code UGL bar.
- Page 12 Ethernet and Cloud Server Settings Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click on >...
-
Page 13: Access Control Setting
Access Control Setting > [Access Control] Click on to enter the access control management interface and set relevant parameters of access control. Access Control Options Main Menu Access Control Access Control Options Gate Control Mode User Mgt. System User Role COMM. - Page 14 Detection Management Settings System Detection Management Click on > [ ] > [ ] to enter the setting interface ❶ You can set the value of High temperature alarm threshold, and enable the Temperature over the range; access denied and the Trigger external alarm, the device will send an alarm prompt when the temperature of the user detected exceeds the set value, meanwhile the user will be forbidden to access, as shown in the following figure.
- Page 15 Note: The effective distance for temperature detection is within 30-50cm for the palm and 0.3-2m for the face. Recommended for indoor use only. Temperature measurement data is only for reference, and not for medical use. Remove the mask to register the face, and wear the mask while recognizing the face.
- Page 16 As shown in the following figure. Real-Time Monitoring Welcome, admin 2020-05-22 11:03:07 Real-Time Monitoring Temperature Management Total: Real-Time Monitoring Normal Records Abnormal Temperature Statistics Panel Temperature Raw Record Name: UnregisterUser Department: NULL Abnormal Temperature Record Temperature: 36.57°C 52.1 C Mask: Department Daily Statistics Mask: None...
- Page 17 QR Code as the Mobile Credential On the server, choose [System] > [Authority Management] > [Client Register] to add a registered App client. Open the APP, enter the IP address or domain name of the server, and its port number, scan the Register QR-code. After the connection is successful, tap on Employee to switch to the Employee Login screen.
- Page 18 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright 2021 ZKTECO CO., LTD. All Rights Reserved.