TW-MI-S-01
Wireless battery
powered input module
IMPORTANT TO CONSIDER
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Large metal objects or structures
• Fluorescent lighting fittings
• Fluorescent lighting fittings
• Metal ceiling structures
• Metal ceiling structures
• IT cabling.
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
EN54 approved environmental temperature range is -10°C to +55°C
UNBOXING
UNBOXING
• When unboxing the input module you will find the unit and its lid.
• When unboxing the input module you will find the unit and its lid.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• This comes with pre-formed mounting holes to drill out and mount the backbox.
• Securing screws are supplied for the lid.
• Securing screws are supplied for the lid.
• A resistor pack is supplied for the monitored connection (10K R
• A resistor pack is supplied for the monitored connection (10K R
For more information, please refer to the complete product manual.
For more information, please refer to the complete product manual.
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
WIRELESS BATTERY POWERED INPUT MODULE
WIRELESS BATTERY POWERED INPUT MODULE
QUICK START GUIDE
QUICK START GUIDE
THE BOX
INSIDE THE BOX
THE BOX
THE BOX
INSIDE THE BOX
QR code
• 1 x Input Module
QR code
Taurus QR code
• 1 x Input Module
Part number
• 2 x CR123A batteries
Manual QR code
Part number
• 2 x CR123A batteries
Product name
• 4 x Securing screws
Product code
Product name
• 4 x Securing screws
• 1 x Resistor pack
Product name
• 1 x Resistor pack
• 1 x Product manual
• 1 x Product manual
• 1 x Quick start guide
• 1 x Quick start guide
• 1 x QR code
• 1 x QR code
and 5.6K R
).
EOL
AL
and 5.6K R
).
EOL
AL
TW-MI-S-01
TW-MI-S-01
MOUNTING STEPS
MOUNTING STEPS
The Input Module is designed to meet IP65 rating, suitable for external mounting.
The Input Module is designed to meet IP65 rating, suitable for external mounting.
Proceed as follows to complete the device installation.
Proceed as follows to complete the device installation.
Remove the lid from the back box, removing the screws
on the corners.
Remove the lid from the back box, removing the screws
on the corners.
• To retain IP rating, please ensure you use the outer holes
on the casing.
• To retain IP rating, please ensure you use the outer holes
• Using a pencil, mark through the outer holes on the desired
on the casing.
surface you will attach the unit to.
• Using a pencil, mark through the outer holes on the desired
• Using a suitable-sized drill bit (6 mm) drill the marked screw
surface you will attach the unit to.
points on your chosen surface.
• Using a suitable-sized drill bit (6 mm) drill the marked screw
• Ensure you use the correct fixings for the type of surface
points on your chosen surface.
you are mounting to.
• Ensure you use the correct fixings for the type of surface
• Screw the backbox to the desired surface using all fixing holes
you are mounting to.
and appropriate-sized roundhead screws (not countersunk).
• Screw the backbox to the desired surface using all fixing holes
and appropriate-sized roundhead screws (not countersunk).
1
1
• Remove the appropriate knock out on the underside or lower
rear of the casing, install the M16/20 IP rated gland.
• Remove the appropriate knock out on the underside or lower
• Note: pay attention to avoid damages to the PCB, while
rear of the casing, install the M16/20 IP rated gland.
removing the knock out, or remove it before starting.
• Note: pay attention to avoid damages to the PCB, while
removing the knock out, or remove it before starting.
3
3
ON
1
ON
1
DIP
SWITCH
DIP
SWITCH
LED
LED
BATTERY
COMPARTMENTS
BATTERY
COMPARTMENTS
• Ensure the switch on the PCB is in position ON.
• Fit the 2x CR123A batteries ensuring you have checked
• Ensure the switch on the PCB is in position ON.
they are the correct way round observing the polarity
• Fit the 2x CR123A batteries ensuring you have checked
indications on the PCB.
they are the correct way round observing the polarity
• The LED will signal 4 times red.
indications on the PCB.
• Move the switch on the PCB to position 1. The LED will blink
• The LED will signal 4 times red.
few seconds green and then signal alternatively green/red
• Move the switch on the PCB to position 1. The LED will blink
4 times.
few seconds green and then signal alternatively green/red
4 times.
L50-MIS-0001 (Rev_P.1)
L50-MIS-0001 (Rev_P.2)
L50-MIS-0001 (Rev_P.1)
2
2
4
4
Need help?
Do you have a question about the TAURUS TW-MI-S-01 and is the answer not in the manual?
Questions and answers