Advertisement
Quick Links
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737)
BEFORE YOU BEGIN
❒
Read these instructions completely and carefully.
IMPORTANT –
•
inspector's use.
IMPORTANT –
•
ordinances.
Note to Installer –
•
Consumer.
Note to Consumer –
•
• For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING
grounded 3-hole, 120V receptacle as required by the National Electrical Code.
FOR YOUR SAFETY:
WARNING –
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
TOOLS YOU WILL NEED
❒ Phillips screwdriver
❒ Pencil
❒ Awl or punch
❒ Level
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
Save these instructions for local
Observe all governing codes and
Be sure to leave these instructions with the
Keep these instructions for future reference.
—
This oven must be plugged into a properly
Before beginning the
❒ Drill with
" bit or #35
7
⁄
64
❒ Tape measure
❒ Scissors (optional)
.
Built-In Trim Kits
JX2027 and JX2030
or
Visit our Website at:
• Do not alter or modify any part of this kit or the oven.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and
electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC and JEB1860SMSS.
PARTS INCLUDED
PART
NOTE: This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.
1
ge.com
QUANTITY
❒
Trim Frame
❒
Bottom Duct
❒
Side Duct
❒
4 mm x 12 mm
Round-Head Screws (21 required
for installation)
❒
4 mm x 14 mm
Flat-Head Screws
(4 required for
installation)
❒
Anti-Tip Brace
❒
Anti-Tip Bracket
❒
Upper Duct
❒
Top Bracket
❒
Bottom Bracket
❒
Templates
1
1
1
23
6
1
1
1
1
1
2
Advertisement
Related Manuals for GE JX2027
Summary of Contents for GE JX2027
- Page 1 Be sure to leave these instructions with the • Product failure due to improper installation is not covered under the Warranty. Consumer. • This kit is UL listed for installation alone or over any GE/GE Profile Note to Consumer – •...
- Page 2 Installation Instructions ❒ CUTOUT DIMENSIONS ❒ INSTALL THE ANTI-TIP BRACE Draw a line on the cutout floor at the center of Models 27″ 30″ the cutout, and extend the line 1/2″ down the ″ ″ Height ⁄ ⁄ face of the cabinet. ″...
- Page 3 Installation Instructions ❒ ❒ INSTALL ANTI-TIP BRACKET INSTALL SIDE DUCT AND AND BOTTOM DUCT UPPER DUCT (cont.) Set the microwave upright, being careful not to bend the Disconnect the microwave oven before proceeding with the front flange. Remove the one existing screw from the left installation.
- Page 4 Installation Instructions ❒ ❒ CHECK LEVELING INSTALL THE TRIM FRAME Place the trim frame over the microwave oven with the Check the leveling by placing a level at the front and sides of the curved edge at the top. microwave. It may be necessary to Press the trim frame into the opening until all sides snap add wood shims under the bottom into place.