Summary of Contents for Sam 20 S 1234
- Page 1 INSTRUCTION AND PARTS MANUAL Strong. Simple. Smart. Topcon Control All models from 2023 (400 & 800mm wide floor-belts single and tandem axle) 6 TONNE TANDEM-AXLE 9 TONNE TANDEM-AXLE www.samfarmmachinery.com...
-
Page 2: Model Details
All SAM Machinery products are identified with a unique serial number located on the front of the machine (e.g. ‘20 S 1234’). Please include this number with all parts and servicing enquiries so we can provide you with fast and accurate assistance. -
Page 3: Quality Guarantee
QUALITY GUARANTEE SAM Machinery products are guaranteed against any defects in either material or manufacture for a period of 24 months from delivery date, provided that the equipment is properly maintained and has not been subject to abuse or misuse, operated incorrectly, over loaded or used for purposes other than for which the equipment is designed or is not maintained correctly or if fitted with other than genuine parts. - Page 4 Carry out any pre-use checks as specified. HEALTH & SAFETY RISK ASSESSMENT A hazard identification, assessment and control procedure has been conducted on a representative SAM Spreader and where necessary appropriate risk control measures have been outlined below; HAZARD HARM...
-
Page 5: Basic Maintenance
BASIC MAINTENANCE To keep your SAM Spreader in excellent working condition, please follow these basic maintenance procedures as you go. Keep your machine fairly clean and very well greased. Before each use; check the hydraulic system for signs of oil leaks or wear. Check there is no play in the spinner bearings by lifting up on the spinner discs. - Page 6 Lime. You can choose any spread width in the set-up mode. For all TOPCON set up instructions - see the TOPCON manual provided. There is also a video on the SAM Machinery YouTube channel - ‘How to set up your SAM Computer control Spreader’.
- Page 7 SET-UP AND OPERATION HYDRAULIC OPERATION Always ensure tractor oils are kept in excellent condition. Beware when changing your Spreader between different tractors. Pump oil out of the hoses unless they use the same hydraulic oil. CONNECTING THE HYDRAULICS Connect the red ‘Spinner’ pressure hose to a pressure port on a tractor SCV (Selective Control Valve). Connect the black ‘Floor’...
- Page 8 BULK DENSITY TO MEASURE BULK DENSITY OF PRODUCT BEING SPREAD This quick process is very important for spread accuracy. Turn on the scales. Put the empty scoop on the scales. Then zero the scale (by pressing the TARE button). Take scoop off the scales and fill to the top. Product must be level with the top. Put the scoop and product back on the scales and weigh it.
- Page 9 Load cells * Wheel & Tyre, Tow Hitch and Hub & Stub set-up varies depending on machine model, size and year of manufacture. NB: the image below is showing a 6 Tonne SAM Spreader with Computer Control and a 400mm wide-belt.
- Page 10 Please include the machine serial number with all parts and servicing enquiries. NB: the image below is a 9 Tonne SAM Combo Spreader with Computer Control and an 800 wide floor belt. NB: the image opposite is a 6 Tonne SAM Combo Spreader with Computer Control and an 800 wide floor belt.
- Page 11 SPARE-PARTS FOR TOPCON CONTROL SPREADER MACHINE REAR-VIEW - For 3.8, 5, 6 Tonne Computer Controlled Spreaders - Both 400 & 800 wide belts REFERENCE PART NUMBER DESCRIPTION QTY. P5077 Danfoss OMP50/9 Hydraulic Motor specify left/right P3040 Skirt Pressing (S/S) - (inc. Rubber + Rivets) P4686 Skirt Rubber &...
- Page 12 * Floor-Belt and Chain, Skirt Pressings, Couplings and Back/Front Shafts vary depending on machine model, size and year of manufacture. Please include the machine serial number with all parts and servicing enquiries. NB: the image above is a 9 Tonne SAM Combo Spreader with an 800 wide floor belt.
- Page 13 BEARINGS / SEALS HUB MAKE / MODEL HUB SIZE BEARINGS SEAL HUB CAP ADR Mk7 70sq 30213/32210 100 x 120 x 8 Screw on ADR Mk7 80SQ 32215/32212 130 X 77 Screw on...
- Page 14 SPREADING TABLES The spreading table below is fixed beside the back door of each SAM Fertiliser Spreader. The required fertiliser application rate can be set by adjusting the back door and viewing the spreading table sticker to achieve the desired rate per hectare - setting the pointers on the back door level with the selected box.
-
Page 16: Troubleshooting
TROUBLESHOOTING If you are experiencing something not listed here, please contact your local dealership. QUESTION / PROBLEM SOLUTION Densities can vary significantly. To get an accurate density always weigh your product or ask your supplier. 3.8t Combo Spreader 3.6t of Superphosphate 4.8t of Lime 2.3t of Urea What is the Spreader bin capacity? - Page 17 TROUBLESHOOTING QUESTION / PROBLEM SOLUTION Standard SAM Fertiliser Spreaders are fitted with two OMP50 What hydraulic oil flow is required? hydraulic motors running in series, requiring an external oil flow of 50 litres per minute plus 40 litres for the floor. For a total requirement of 90 litres per minute.
- Page 18 Check front and back mollybushes for excessive wear and tear. Should be no ‘play’. Vanes Check vanes. Bolts torqued to 55Nm. Spinner tubes Check spinner tube bolts to discs torqued to 55Nm. Please keep your checks up for the lifetime of your SAM.
- Page 19 www.samfarmmachinery.com instagram / @newsfromSAM facebook / @sammachineryaustralia...
Need help?
Do you have a question about the 20 S 1234 and is the answer not in the manual?
Questions and answers