Yazoo/Kees CS1372 Operator's Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Collection System

Operators Manual

Models:

111793 / CS1372

Parts Manual

Please read these instructions carefully and make

sure you understand them before using the machine.

MANUAL NO. 111725 REV IR (02/18/05)

Get other manuals https://www.bkmanuals.com

Table of Contents

Summary of Contents for Yazoo/Kees CS1372

Page 1 Collection System Operators Manual Models: 111793 / CS1372 Parts Manual Please read these instructions carefully and make sure you understand them before using the machine. MANUAL NO. 111725 REV IR (02/18/05) Get other manuals https://www.bkmanuals.com...
Page 3: Table Of Contents
INDEX Operators Guide Features and Controls .............. 4 General Information ..............5 Safety Procedures ..............5 Unpacking Instructions ............. 7 Assembly Instructions .............. 7 Collection System .............. 7 Blower/Drive Kit ............... 11 Operating the Collection System ........13 Maintenance and Service Instructions Transport ................
Page 4: Features And Controls
FEATURES & CONTROLS HOOD INLET LATCH SUPPORT LINKAGE SUPPORT BRACKET HITCH HITCH BRACKET REAR GUARD WEIGHT BAR DRIVE KIT HOSE CAST WEIGHT BLOWER ASSEMBLY NOTE: Your Front Weight Bar may look different from those shown in this diagram. Get other manuals https://www.bkmanuals.com...
Page 5: General Information
SAFETY RULES Safety Procedures General Information This manual will assist you in the safe operation 1 - Training: and proper maintenance of your Husqvarna • Read the Operator’s manual. If the operator(s) equipment. Read it thoroughly before attempting or mechanic(s) can not read English it is the to operate the machine.
Page 6 SAFETY RULES 3 - Operation • Use care when loading or unloading the machine • Never run an engine in an enclosed area. • Only operate in good light, keeping away from into a trailer or truck. holes and hidden hazards. •...
Page 7: Unpacking Instructions
ASSEMBLY Unpacking Instructions Cut plastic tie securing the hitch to the crate top. Remove the top of the crate. Remove the plastic bag. Remove the hose. Remove the sides and ends of the crate. Remove the mounting kit and drive kit boxs from the corner of the crate. Cut the two plastic ties that secure the hitch assembly to the pallet.
Page 8 ASSEMBLY Remove the (10) 5/16 carriage bolts that secure the standard rear guard to the straps and skid plates. Remove the standard rear guard. Replace with the collection rear guard, and secure with the carriage bolts that were just removed. Figure 2. FIGURE 2 1.
Page 9 ASSEMBLY Place the hood assembly on to the hitch Open the hood and secure the (2) springs assembly. Place both hood hinges between to the bolts on the hood assembly and the the upper hitch mounts on the hitch assembly. hitch assembly.
Page 10 ASSEMBLY With the hood open, secure the (3) bags in place. The back of the bags will hook over the mounting tabs on the hitch assembly. Figure 5. Close the hood, and latch the draw latch over the draw latch keeper on the hitch assembly. Figure 5.
Page 11: Blower/Drive Kit
ASSEMBLY Blower/Drive Kit Open the drive kit box and remove all of the components. Place the deck in the lowest cutting height. Remove the right side belt shield from the deck. Remove the deck belt from the right side pulley. Remove the deck pulley, but keep the hardware at hand for re-installation.
Page 12 ASSEMBLY Place the blower pin weldments in the tubes Place the belt shield on the deck and check on the blower assembly. Figure 1. for clearances between the deck pins and the shield. Rest the blower assembly on the end and Mark the 4 holes in the pin weldments and align the deck opening and the blower center punch.
Page 13: Operating The Collection System
OPERATION Operating the Collection System NEVER USE THE COLLECTION SYSTEM WITHOUT THE BLOWER ASSEMBLY AND HOSES SECURELY ATTACHED. Make sure hoses are connected at both ends. Inspect hoses prior to each use. Do not use the unit on slopes greater than 10 degrees.
Page 14: Transport
SERVICE AND MAINTENANCE Transport For best results, clean poly mesh inside hood regu- larly. Instructions for doing this can be found in WARNING the Service section of this manual. The collection system bags must be com- pletely empty or removed while driving for- ward onto a trailer.
Page 15: Caring For Vacuum Hoses
SERVICE AND MAINTENANCE Caring For Hoses Caring For Bags 1. Inspect hoses before each use. If hoses have Inspect the bags before each use. If bags have excessive wear, tears, or punctures, replace excessive wear, tears or punctures, replace im- immediately.
Page 16: Troubleshooting Guide
SERVICE AND MAINTENANCE Troubleshooting Guide DANGER Before servicing unit, wait for all moving parts to come to a complete stop. Turn engine off and remove the spark plug wire. PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. 1. Blower, hose or hood inlet clogged. 1.
Page 17 SPINDLE DRIVE ASSEMBLY NOTE: Your Front Weight Bar may look different from those shown in this diagram. Get other manuals https://www.bkmanuals.com...
Page 18: Hood Assembly
HOOD ASSEMBLY 99 07-30 (x 2) 99 06-45 (x 6) 99 06-13 (x 2) 11 11-81 (x 2) 11 00-33 (x 8) 11 11-72 97 69-79 (x 8) 11 11-77 (x 2) 20 06-84 (x 30) 99 05-98 (x 16) 97 69-78 (x 8) 20 06-84 (x 30) 20 06-84 (x 30)
Page 19: Hitch Assembly
HITCH ASSEMBLY 11 11-62 (x 2) 99 05-63 (x 20) 97 69-79 (x 22) 99 05-63 (x 20) 11 11-58 (x 2) 11 11-87 (x 4) 99 05-80 (x 3) 99 02-54 (x 4) 99 06-25 (x 4) 11 11-67 11 11-71 539 97 69-79 (x 22) 97 69-78 (x 3)
Page 20: Blower Assembly
BLOWER ASSEMBLY 10 25-35 99 07-17 (x 12) LOCKING COLLAR 99 01-96 (x 3) THIS SIDE UP 10 26-91 (x 5) 10 67-86 (x 2) 11 13-31 10 57-43 10 67-41 99 02-08 10 81-20 (x 12) 10 57-85 99 07-17 (x 12) 99 00-74 (x 10) 88 03-16 (x 7) 10 04-72 (x 3)
Page 21 BLOWER ASSEMBLY 11 17-52 10 81-20 (x 12) 11 17-73 99 05-98 (x 12) 99 00-74 (x 10) 97 69-79 (x 4) 99 00-74 (x 10) Get other manuals https://www.bkmanuals.com...
Page 22: Weight Kit
WEIGHT KIT 20 09-21 11 13-13 10 20-49 (x 2) 10 80-96 (x 2) 11 12-59 (x 2) 97 69-41 (x 4) ER92531 (x 3) 99 05-17 (x 4) 97 69-79 (x 4) Get other manuals https://www.bkmanuals.com...
Page 23: Mounting Kit
MOUNTING KIT 10 29-98 (x 2) 97 69-79 (x 6) 99 05-63 (x 6) 99 06-54 (x 2) 11 12-08 (x 2) 11 12-07 (x 2) REF. 09 70-76 97 69-89 (x 2) 10 25-63 (x 4) 11 11-91 (x 2) 10 87-36 (x 2) 11 12-10 (x 2) 11 11-97...
Page 24: Bag Assembly
BAG ASSEMBLY 11 00-63 99 07-17 (x 7) 99 03-16 (x 7) 99 07-99 (x 7) 11 11-66 99 06-92 (x 3) 99 07-17 (x 7) 11 11-68 Get other manuals https://www.bkmanuals.com...
Page 25: Drive Kit
DRIVE KIT ASSEMBLY 111775 - 72 INCH DECK 11 16-76 10 57-44 10 57-43 97 69-98 10 44-11 (x 4) 10 89-51 11 13-44 99 05-46 (x 4) 10 89-44 (x 2) 99 01-34 (x 4) Get other manuals https://www.bkmanuals.com...
Page 26: Parts Description
PARTS DESCRIPTION PART NUMBER DESCRIPTION 0 70-76 HOSE CLAMP 6”-& 7” 10 01-41 HCS, 7/16-20 X 1 1/2, GR5 10 04-13 RHSNB, 3/8-16 X 1 1/4, GR5 10 04-72 RHSNB, 5/16C X 1 1/4 10 13-31 NUT, 1/2C, NYLOC 10 17-21 HCS, 5/16-18 X 2 3/4, GR5 10 20-49 CLEVIS PIN...
Page 27 PARTS DESCRIPTION PART NUMBER DESCRIPTION 11 11-87 NUT, 1/2-13, WHIZLOCK 11 11-90 LATCH 11 11-91 SPRING 11 11-92 HAIRPIN 11 11-97 REAR GUARD 11 11-99 HITCH BRACKET, LEFT (NOT SHOWN) 11 12-06 HITCH PIN 11 12-07 TURNBUCKLE, 1/2” 11 12-08 SUPPORT LINKAGE, LH 11 12-10 SUPPORT LINKAGE...
Page 28 PARTS DESCRIPTION PART NUMBER DESCRIPTION 99 02-47 LOCKWASHER, 7/16 99 02-54 WASHER, 1/2 99 03-16 RHSNB 5/16-18 X 5/8, GR5 99 05-17 WASHER, 3/8 99 05-46 NUT, 3/8-16, CENTERLOCK 99 05-63 HCS, 3/8-16 x 1, GR5 99 05-80 HCS, 1/4-20 X 3/4 99 05-85 NUT, 5/16C 99 05-98...
Page 29 Get other manuals https://www.bkmanuals.com...
Page 30 Get other manuals https://www.bkmanuals.com...
Page 31 Get other manuals https://www.bkmanuals.com...
Page 32 Get other manuals https://www.bkmanuals.com...

This manual is also suitable for:

111793