Related Manuals for Blomberg LDF63440X
Summary of Contents for Blomberg LDF63440X
- Page 1 Dishwasher User’s Manual LDF63440X 15 7774 0100_AA_BLOOMBERG_E9L_EN/ 07-04-23.(13:58)
- Page 2 Dear Customer, Please read this user manual before using the product. Thank you for choosing this Blomberg product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents before using the product.
-
Page 3: Table Of Contents
CONTENTS 1 SAFETY INSTRUCTIONS Upper basket height adjustable rack ....27 Lower basket bottle wire ........27 Intended Use ............. 4 Upper basket multipurpose service rack ..27 Safety for children, vulnerable persons and pets 4 Adjusting the height of the upper basket ..28 Electrical safety .......... -
Page 4: Safety Instructions
This product must be used to Safety Instructions do the domestic type dishes • This section contains safety only. instructions that will help get This product is not suitable for protected against risks of commercial or collective use. personal injury or property damage. -
Page 5: Electrical Safety
maintenance works should multi-sockets or adapters to not be performed by children operate the product. unless they are supervised by Plug must be easily someone. accessible. If this is not Keep packaging materials possible, the electrical away from children. There installation where the product is the risk of injury and is connected must contain... -
Page 6: Installation Safety
placing the product into its and harm your furniture. location after installation or Do not install the product cleaning procedures. close to heat sources (heater, stove and etc.) or under the Installation Safety cooking area of a hob. • To make the product ready for •... -
Page 7: Operational Safety
at the hoses. other loads on the door; otherwise, the product may NOTICE Connect the water inlet tilt. hose directly to the water tap. Maximum washing capacity Pressure coming from the tap of the product is stated in the should be 0.03 MPa (0.3 bars) section called “Technical minimum and 1MPa (10 bars) Specifications”. -
Page 8: Interior Lighting
Instructions Do not wash the product by spreading or pouring water Compliance with WEEE onto it. Directive and Disposing of Do not use sharp or abrasive the Waste Product tools when cleaning the This product complies with product. Do not use home EU WEEE Directive (2012/19/ cleaning products, detergent, EU). -
Page 9: Package Information
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive. Package information Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. - Page 10 Note for test institutions: Frequency Band : 2.400-2.484 Ghz Data required for performance tests shall Max. Transmission Power : < 100mW be provided upon request. Requests can Conformity declaration for be e-mailed to the following address: UKCA dishwasher@standardloading.com Do not forget to provide the code, stock number and serial number of the product ARÇELİK hereby declares that this to be tested in your request e-mail along...
-
Page 11: Technical Specifications
Technical specifications Maximum washing capacity (check the energy label and Programme data and average consumption values table given on Quick Guide. ) Height (check installation document for installation) Width: 60 Depth: 57 Power input: 220-240 V, 50 Hz * Total power 1800-2100 W * Heater power: 1800 W * Total current: 10 A * Pump power: 90 - 125 W *... -
Page 12: Your Dishwasher
Your dishwasher Overview 1. Upper basket 2. Upper impeller 3. Lower impeller 4. Cutlery basket (depends on model) 5. Door 6. Rating Label 7. Control panel 8. Detergent dispenser 9. Lower basket 10. Filters 11. Salt reservoir lid 12. Upper basket rail 13. -
Page 13: Installation
Installation Appropriate installation location In the area where this product is Read “Safety Instructions” section first! installed, there must not be a lockable, Installation procedures must always be sliding or hinged door that will restrict performed by the manufacturer, authorised full opening of the product’s door. -
Page 14: Aquavoid™ Plus
aquAvoid™ plus Permitted water temperature: up to 25°C ( 60°C for products equipped (depends on the model) with aquAvoid™ plus; please refer The aquAvoid™ plus system protects to aquAvoid™ plus section ) against water leaks that may occur at the The dishwasher may not be connected to hose inlet.Water contact with the valve box open warm water devices or flow-through... -
Page 15: Connection To The Drain
Connection to the drain Electrical connection Water discharge hose can directly be Connect the product to a grounded connected to the drain hole or sink’s outlet protected by a fuse complying drainage. See the installation manual with the values in the "Technical supplied with your machine for detailed specifications"... -
Page 16: Fitting A Different Plug
pin face of the plug. Fuse covers are available from any good electrical store. Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows: Connect the green - yellow or green (earth) wire to the terminal in the plug... -
Page 17: Preparation
Preparation Read “Quick Guide - Adjusting Water Softening System” before this section! The regeneration of the water softening Read “Safety Instructions” section first! system can be done in all programmes Tips for energy saving during drying step. When regeneration occurs, duration, energy and water Following information will help you use the consumption of the programme increase. -
Page 18: Adding Salt
Adding salt Water softening system needs to be regenerated in order for the product to operate with the same performance continuously. Dishwasher salt is used for this purpose. Use only special softening salts produced particularly for the dishwashers in your machine. You can put about 2 kg of softening It is recommended to use granule- or salt into the salt reservoir. - Page 19 the manufacturer of the detergent for further questions. Do not put solvents into the detergent dispenser. There is the risk of explosion! Put the detergent into the detergent dispenser just before operating the machine as illustrated below. 1. Push the latch to right to open the 3.
-
Page 20: Tablet Detergents
Tablet detergents 3. After the empty washing cycle, review the user manual and readjust the water In addition to the conventional tablet hardness level so as to suit the water detergents, there are also commercially supply. available detergent tablets that show water 4. -
Page 21: Items Not Suitable For Washing In The Dishwasher
3. Slightly press the point (B) of the Decorative prints of chinaware as well reservoir lid to close it. as aluminium and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing as well. Some delicate glass types and crystals may become dull in time. - Page 22 Suggestions for loading the dishwasher Improper Loading Of Dishware Lower basket Upper basket Improper Loading Of Dishware 22/EN...
-
Page 23: Cutlery Basket
Cutlery basket Cutlery basket (depends on model) (depends on model) Cutlery basket is designed to wash your Cutlery basket is designed to wash your dishes such as knife, fork, spoon, etc. in an dishes such as knife, fork, spoon, etc. in an efficient manner. -
Page 24: Collapsible Lower Basket Tines
Collapsible lower basket tines Collapsible lower basket tines (depends on model) (depends on model) There are foldable tines (A) located at There are foldable tines (A) located at the lower basket of the machine are the lower basket of the machine are designed for an easier placement of large designed for an easier placement of large pieces such as pans, bowls, etc. -
Page 25: Tray Wash Supports
Tray Wash Supports SoftTouch Accessory (depends on model) (depends on model) Use the supports to wash trays in the The SoftTouch Accessory found in the bottom basket. lower basket of your machine enables a See the Auxiliary functions section for safe washing for your fragile glasses. -
Page 26: Lower Basket Multipurpose / Height Adjustable Service Rack
Lower basket multipurpose / To close the racks: 1. Fold the rack (A). height adjustable service rack 2. Slide the rack up (B). (depends on model) This accessory located at the lower basket 3. Put the rack in vertical position (C). of your machine allows you to easily wash 4. -
Page 27: Upper Basket Height Adjustable Rack
Upper basket height adjustable Upper basket multipurpose rack service rack (depends on model) (depends on model) Use the lower and upper parts of the height This accessory located at the upper basket adjustable racks in the upper basket of of your machine allows you to easily wash the machine by sliding them down or up pieces such as extra long ladles and bread according to the heights of the glasses,... -
Page 28: Adjusting The Height Of The Upper Basket
Adjusting the height of the upper To lower the basket, while it is in the uppermost position; basket 1. Hold the upper basket wires with both (depends on model) hands, slightly lift up the basket and The upper basket height adjustment simultaneously push and release the mechanism has been designed for you to latches shown in the figure (B). - Page 29 Repeat the same operation if the height is Adjusting the height of the upper not adequate. basket (depends on model) Upper basket height adjustment mechanism is designed so that you can create wide spaces on the upper or lower compartment of the machine by adjusting the basket upwards or downwards either while it is empty or full.
-
Page 30: Bottle And Dish Holder On The Lower Basket
Bottle and Dish Holder on the Tray Washing Support (depends on model) Lower Basket You may use the tray washing supports (depends on model) if you want to wash a tray on your lower Bottle and dish holder (A) on the lower basket. -
Page 31: Height Setting With Empty Basket
Height setting with empty basket Collapsible upper basket wires (depends on model) (depends on model) In this model, the height setting of the You can use collapsible wires when you upper basket may be changed using the need a larger space for your dishes in the wheels which are mounted at two different upper basket of your machine. -
Page 32: Ceiling Cutlery Basket
Ceiling cutlery basket (depends on model) Ceiling cutlery basket is designed to wash your cutlery items such as forks, spoons and etc. by placing them between the bars on the basket. When the central tray is in the lower position, you can load long/high items such as coffee cups, ladles, etc. -
Page 33: Operating The Product
Operating the product 4. Put adequate amount of detergent into Read “Safety Instructions” section first! the detergent dispenser. Read “Quick Quide” before this section. Programme selection When you press the On/Off key, the indicator 1. Press the On/Off button to turn on your lights illuminate on the display for ON machine. - Page 34 Super Gloss Function Functions in Settings Menu (Depends on model) (depends on the model) It provides superior drying performance. Under the settings menu of your product, there are some additional functions that DeepCare function depend on the model. (depends on the model) To access these functions, press and hold The Bottle/Pot washing the Menu key for 3 seconds.
- Page 35 Function Off/On Floor illumination Warning to show that machine is in washing phase (depends on the model) Your machine reflects a light to the floor during the washing process. This light turns off after the washing process is complete. Floor illumination is activated automatically when the washing Changing Warning Sound Volume programme starts and remains lit until...
-
Page 36: Scheduling The Washing Time
Changing the settings while Time Changing Doormatic Settings Delay function is active 1. Press Menu key for 3 second after While the Time Delay function is activated, turning on your machine. you cannot make changes in the washing 2. Use the <- and +> keys to move to “o:” programme, auxiliary functions or the position on the screen. -
Page 37: Adjusting The Amount Of Rinse Aid
Adjusting the amount of rinse The machine will remain silent in pause mode for some time in order to remove the water from the machine 1. After switching on your machine, press and on the dishes completely and to the Menu key for 3 second. have the water softener cleaned, and Some models require pressing Menu then it will resume running in drying... -
Page 38: Water Cut-Off Warning
Leave your dishes in the machine for about 15 minutes to allow them cool down after they are washed. Your dishes will dry in a shorter time if you leave the door of your machine ajar during this period. This process will increase the drying effectiveness of your machine. -
Page 39: Maintenance And Cleaning
Maintenance and Cleaning the filters cleaning Clean the filters at least once a week in order for the machine operates efficiently. Read “Safety Instructions” section first! Check if food residues are left on the filters. Unplug the product and turn off the If there are food residues on filters, take tap before attempting any cleaning them out and clean well under running... -
Page 40: Cleaning The Hose Filter
Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation (such as sand, dirt, rust, etc.) can be prevented by means of the filter attached to the water inlet hose. Check the filter and the hose regularly and clean them if necessary. -
Page 41: Cleaning The Impellers
Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently. Lower impeller Do not try to rotate the impeller by Check if the holes on the lower impeller (1) holding its ends. Trying to rotate the are clogged. -
Page 42: Troubleshooting
Troubleshooting Machine does not start. • Power cable is unplugged. >>> Check if the power cable is plugged in. • Fuse is blown. >>> Check the fuses in your house. • Water is cut. >>> Make sure that the water inlet tap is open. •... - Page 43 • Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. • Machine is unloaded right after the programme is over. >>> Do not unload your machine right after washing process is completed.
- Page 44 There is a different odour in the machine A new machine has a peculiar odour. It will fade out after a couple of washes. • Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”.
- Page 45 • Opening of the detergent dispenser lid is prevented during washing. >>> Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers. • Detergent is stored under unsuitable conditions. >>> If you are using powder detergent, do not store the detergent package in humid places.
- Page 46 Foam forms in the machine. • Dishes are washed with hand-wash detergent by hand but not rinsed before placing them into the machine. >>> Hand-wash detergents do not contain antifoam. There is no need to hand-wash the dishes before placing them into the machine. Removing the coarse soil on the dishes under tap water, with a tissue paper or fork will be sufficient.
-
Page 47: Guarantee
Guarantee Details light bulbs. • Repairs necessary as a direct or Your new Blomberg product is guaranteed indirect result of: against faulty materials, defective Accidental damage, misuse or abuse components or manufacturing defects. of a product. - Page 48 Optional extras, where available (i.e. extendable feet) are supplied on a chargeable basis only. Does Blomberg offer replacements? This is a repair-only guarantee. On occasion the Manufacturer may at its sole discretion, replace your product with a new product instead of carrying out a repair. Where a replacement is offered, this would normally be an identical model, but when this is not possible, a model of similar specification will be provided.
- Page 49 When will the repair take place? Our engineers work Monday to Friday 9.00am to 5.00pm. Appointments outside these hours may be possible at the sole discretion of the Manufacturer but cannot be guaranteed. Whilst our Engineers will endeavour to minimize inconvenience and to meet requests for specific timed appointments, this cannot be guaranteed.
- Page 50 Should you experience any difficulty in obtaining service contact the Blomberg Customer Helpline on Tel: 0333 207 9870 or e-mail: customerservice@support.Blomberguk.com ………………………………………………..............