Realtime TD1D - Fingerprint Access Control System Manual
Product Overview and Installation Instruction
Applicable Models
S.N. | Functions |
1 | Dark-background fingerprint reader |
2 | Built-in card reader |
3 | User verification with fingerprint or card |
4 | Numeric keys |
5 | Tamper alarm |
6 | Reading head for data output |
7 | 86mm box-type panel for installation |
Operating Environment:
Room temperature: -20°C-+50°C
Relative humidity: 95% O
Operating Voltage & Current:
Input DC: +12V
Standby current: 560mA
Operating current: 120mA
Suggested finger: index finger, middle finger or ring finger instead of thumb or little finger
- Correct method:
Use the finger to evenly press the center of fingerprint are
- Wrong methods:
Ports & Wiring Diagram
Diagram A instructions is electricity lock, using a special power supply access of the connection mode;
Wiring Schematic Diagram B instructions is electricity lock and fingerprint access to share a power supply.
Administrator Operation
- Press(*) and there is a beep while the red light turns on
- Enter administrator password (initial password: 123456)
- Verification request succeeds(while the blue light turns on)
- Exit (by pressing "#")
Remarks: once verification request succeeds, 't is allowed to register administrator and the initial password will be out of use
Registering administrator
- Enter administrator password for Verification, once verification request succeeds ( the blue light turns on)
- Press(*1)and the orange light turns on
- Registering administrator via fingerprint or card (input fingerprint twice or red card once)
- Once Registration request succeeds there is long beep the blue light blink once
- Exit (by pressing{#}
Remarks:
- It is allowed to register at most 5 administrators via fingerprint or card
- In case administrator quantity reaches the maximum value, they will be cleared according to serial number.
Missing administrator password
- Power off this device and dismantle it
- Power on tamper switch to give an alarm, =>. for 30 seconds
- Enter initial password(*123456) the blue light turns on
- Register administrator again
- Exit (by pressing "#")
Registering User
Register Users Automatically
- Enter administrator password for verification. Once verification request succeeds (the blue light turns on)
- Register administrator via fingerprint or card(input fingerprint twice or read card once)
- Once registration request succeeds
- Exit (by pressing "#")
Register Users by Adding Employee ID
- Enter administrator password for verification Once verification request succeeds, (the blue light turns on)
- Enter employee ID #(1-4 digits)
- Register user via fingerprint card or password (input fingerprint twiceread card once or enter password twice
- Once registration request succeeds there is a long beep and the blue light blink once
- Exit (by pressing #")
User Operation
User Verification via Fingerprint or Card
- Standby mode
- Input fingerprint or read card
Verification request fails. (It beeps twice and the red light turns on) - Verification request succeed(There is a long beep sound and the blue light blinks once.)
User Verification via Password
- Standby mode
- Enter employee ID press # to for confirmation and enter password and pressing (#)
Verification request fails. (It beeps twice and the red light turns on) - Verification request succeed (There is a long beep sound and the blue light blinks once.)
Deleting Users
Delete a User
- Enter administrator password for verification, Once verification request succeeds ( the blue light turns on)
- Press [*2] or enter administrator password
- Enter employee ID# or read card
- In case of incorrect ID# fingerprint or card there is two beeps and he red light turns on
- In case the user is in use delete it. is a long beep There and the blue light blinks once
- Exit (by pressing "#")
Delete All Users
- Enter administrator password for verification Once verification request succeeds (the blue light turns on)
- Press [*2] or enter administrator password
- enter (0000#)
- Delete all users There is a long beep and the blue light blinks once
- Exit (by pressing "#")
Access Control System Management
System Settings
- Enter administrator password for verification(Once succeeds verification request (the blue light turns on)
- Press [*9] and the orange light turns on
- Set system Press
[1] for menu initialization press
[2] for system initialization press
[3] to delete administrator and then press [#] for confirmation - Exit (by pressing "#")
Setting Unlocking Time
- Enter administrator password for verification(Once succeeds verification request the blue light turns on
- Press [*3] and the orange light turns on
- Set unlocking time (0-99seconds and press # to for confirmation)
- Setup succeeds There is a long beep and the blue light blinks once
- Exit (by pressing "#")
Note: 5 seconds have been set as factory default.
Unpacking
Description | Specifications | Quantity | Remarks |
Device | | 1 | |
Packaging box | | 1 | |
Plastic plugs | 4mmx28mm | 4 | For mounting and fixing |
Self-tapping screws | 4mmx28mm | 4 | For mounting and fixing |
Diode | 1n4007 | 2 | |
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Realtime TD1D - Fingerprint Access Control System Manual
Need Assistance?
Do you have a question about the TD1D that isn't answered in the manual? Leave your question here.