Abble 300571 Quick Start Manual

BRANCH SHAPING INSTRUCTIONS:
Branch shaping is best performed during assembly procedure but can be done, if preferred, when tree
assembly is completed.
PRE-LIT TREE NOTE: lf your tree is pre-lit, and not a PowerConnect tree, it is recommended that the
light plugs between sections be connected prior to or at the same time as shaping is performed.
1. Trees are shipped from the factory with the tips of each branch compressed to the center (Figure 1).
Branches should be shaped one row at a time. Make sure that all of the branches of the row to be
shaped have been moved to their lowered position.
2. Starting with the bottom row of the tree bottom section, pull the two branch wing tips out away from
center to about a 45°angle (Figure 2).
3. The smaller individual tips should then be spread out separately (Figure 3). Fiqure 4 shows a fully
shaped branch with wing tips.
4. Follow this same sequence as you work around the bottom row of branches. When completed, move
up to the next branch row and repeat.
5. As you work your way up branch rows, the wing tip style branches will diminish, but branches will
otherwise shape similarly. Figure 5 shows a fully shaped branch without wing tips.
6. The top section of the tree will have wrapped branches in place of hinged branches. Gently lower
the branches and shape in a similar manner as the branches in previous sections (Figure 6).
7. Upon completion of the assembly and shaping procedures, walk around the tree and perform
additional shaping to fill any obvious holes or openings.
USE AND CARE INSTRUCTIONS:
Before using or reusing, inspect product carefully. Discard any products that
have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders,
loose connections, or exposed copper wire.
Before storing the product, carefully remove the product from wherever it is
placed to avoid any undue strain or stress on the product conductors,
connections, and wires.
When not in use, store neatly in a cool, dry location protected from sunlight.
ABBLE® 8�. Green Lighted Flocked
Spruce Ar�ficial Christmas Tree
● Thank you for purchasing ABBLE product.
● You are welcomed to visit www.abblestore.com for
more ABBLE products.
®
● We are committed to providing customers with quality
products and a good purchasing experience.
● Need any help regarding purchase or customer service,
please email us by cs@abbleinc.com
(will be responded within 24 working hours)
IMPORTANT SAFETY INSTRUCTIONS：FOR INDOOR USE ONLY
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the
following:
1) To reduce the risk of fire, do not deliberately reposition either bulb or lampholder contact.
2) To reduce the risk of overheating, replace burned out lamps promptly. This is an electrical
product - not a toy! To avoid the risk of fire, burns, personal injury, and electric shock it should not
be played with or placed where small children can reach it.
3) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
When products are used in outdoor applications, connect the product to a Ground Fault Circuit
interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
4) This seasonal use product is not intended for permanent installation or use.
5) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of
heat.
6) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
7) Do not let lamps rest on the supply cord or on any wire.
8) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
9) Do not use this product for other than its intended use.
10) Do not hang ornaments or other objects from cord, wire, or light string.
11) Do not close doors or windows on the product or extension cord as this may damage the wire
insulation.
12) Do not cover the product with a cloth, paper or any material not part of the product when in use.
13) The product employs overload protection (fuse). A blown fuse indicates an overload or short
circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional
strings or products that may be attached to the product. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse rating) and check the product. If the replacement
fuse blows,a short circuit may be present and the product should be discarded.
Read and follow all instructions that are on the product or
provided with the product.
SAVE THESE INSTRUCTIONS
4/4
SKU#300571
®
www.abblestore.com
1/4