Table of Contents
Advertisement
PT-50LCZ70 / PT-56LCZ70 / PT-61LCZ70 / PT-50LCZ7 / PT-56LCZ7 / PT-61LCZ7
How to solve problems indicated by the Error Indication
(The symptom of all errors is that the Lamp goes off)
Note: Before performing troubleshooting, confirm that all connector cables in the unit are connected correctly.
POWER
Indicator
[POWER Indicator one blink]
1
The following voltage lines on the Main P.C.B. is over
current.
• SUB+5V line
• SUB+1.8V line
• SUB+3.3V line
• SUB+1.2V line
• FHD+3.3V line
• DDR+3.3V line
• FHD+1.2V line
The following voltage lines on the Main P.C.B. is over
voltage.
• DT+9V line
• SUB+5V line
• SUB+1.8V line
• SUB+3.3V line
• SUB+1.2V line
• FHD+3.3V line
• DDR+3.3V line
• FHD+1.2V line
2
[POWER Indicator two blinks]
DT+9V line error.
3
[POWER Indicator three blinks]
SUB+5V line error.
[POWER Indicator four blinks]
4
MAIN+3.3V line error.
6
[POWER Indicator six blinks]
AUDIO AMP (IC4501) failure
[POWER Indicator seven blinks]
7
Communication error between Peaks (IC8001) and
TV microcontroller (IC6004) on the Main P.C.B.
9
[POWER Indicator nine blinks]
Communication error between Peaks (IC8001) and
TV microcontroller (IC6004) on the Main P.C.B.
Problem
1. Check the Power P.C.B.
2. If still NG, check DC/DC circuit on the Main P.C.B.
1. Check that Connector CN1102 (Thermal Fuse) on the Main P.C.B. is connected firmly.
2. If still NG, check the Power P.C.B.
3. If still NG, check the following parts of DT+9V line on the Main P.C.B.,
1. Check the following parts of the SUB+5V line on the Main P.C.B.,
and replace if necessary.
• R6134, IC1107, IC6004, and the surrounding parts.
1. Check the following parts of the MAIN+3.3V line on the Main P.C.B.,
and replace if necessary.
• R6106, IC1104, IC6004, Q1104-Q1106, and the surrounding parts.
1. Check the voltage at Pin 5 of IC4501 on the Main P.C.B.
If +3.3V(High), replace IC4501.
If 0V(Low), check the following parts of the SOUND SOS line between Pin 5 of IC4501
and Pin 72 of IC6004 on the Main P.C.B., and replace if necessary.
• Q4502, IC6004, and the surrounding parts.
1. Check the following parts of the PANEL SOS(L) line between Pin L16 of IC8001
and Pin 48 of IC6004 on the Main P.C.B., and replace if necessary.
• IC8001, IC6004, and the surrounding parts.
1. Check the following parts of the PANEL STATUS (SOS(L)) line between Pin G1 of
IC8001 and Pin 13 of IC6004 on the Main P.C.B., and replace if necessary.
• IC8001, IC6004, and the surrounding parts.
Possible Solution
(Refer to "CHECKING THE POWER P.C.B.")
(Refer to "CHECKING THE OPT/TV UNIT (Main P.C.B.).")
(Refer to "CHECKING THE POWER P.C.B.")
and replace if necessary.
• R6011, IC6004, and the surrounding parts.
18
Advertisement
Table of Contents
