König KN-BM20 - Baby Monitor Manual

Table of Contents

Description

Display
Microphone
Speaker
Belt clip
Lock/unlock button	Press the button to lock and unlock the device.
Battery compartment	Refer to the illustration to power the device with 3 AAA batteries.
Volume control / On/off button	Slide the button up to increase the volume and switch on the device. Slide the button down to decrease the volume and switch off the device.
Power cable connection (AC/DC)	Connect the power cable to the power cable connection. Insert the mains plug into the wall socket.
Talk-back button (parent unit) Page button (baby unit)	Press the button to talk through the parent unit to the baby unit. Press the button to page the parent unit.
Page button (parent unit) Lullaby button (baby unit)	Press the button to page the baby unit. Press and hold the button for three seconds to activate or deactivate a lullaby. Press the button to switch between lullabies.
Lullaby button (parent unit)	Press and hold the button for three seconds to activate or deactivate a lullaby. Press the button to switch between lullabies.
Pairing button	Press the button to pair the parent unit and the baby unit.
Sensitivity switch (baby unit)	Set the switch to the "HI" position to set a high sensitivity of the microphone. Set the switch to the "LO" position to set a low sensitivity of the microphone.

Make sure that the parent unit and baby unit are switched on.
Press the pairing button (12) on the parent unit and the baby unit. The pairing icon on the display (1) flashes to indicate that the device is in pairing mode. If pairing is successful, the display shows the normal status.
If pairing is not succesful, repeat the steps above.

Input voltage
Parent unit / Baby unit	5.5 V DC
Power supply	100-240 V AC
Consumption current	500 mA
Battery type	AAA (3x)
Battery duration	6-7 hours
Transmitter power	15-19 dBm
Receiver sensitivity	≤ -90 dBm
Transmission frequency	2.4015 GHz - 2.4525 GHz
Transmission range	300 m
Microphone sensitivity	1-2 m (low sensitivity) 2-6 m (high sensitivity)
Operating temperature	0°C ~ 40°C
Relative humidity	20% - 80%

To reduce risk of electric shock, this product should only be opened by an authorized technician when service is required.
Disconnect the product from the mains and other equipment if a problem should occur.
Do not use the device if the mains cable or mains plug is damaged or defective. If the mains cable or mains plug is damaged or defective, it must be replaced by the manufacturer or an authorized repair agent.
Before use, always check that the mains voltage is the same as the voltage on the rating plate of the device.
Read the manual carefully before use. Keep the manual for future reference.
Only use the device for its intended purposes. Do not use the device for other purposes than described in the manual.
Do not use the device if any part is damaged or defective. If the device is damaged or defective, replace the device immediately.
Do not expose the device to water or moisture.
Do not use the device outdoors. The device is suitable for indoor use only.

Battery safety

Use only the batteries mentioned in the manual.
Do not use old and new batteries together.
Do not use batteries of different types or brands.
Do not install batteries in reverse polarity.
Do not short-circuit or disassemble the batteries.
Do not expose the batteries to water.
Do not expose the batteries to fire or excessive heat.
Batteries are prone to leakage when fully discharged. To avoid damage to the product, remove the batteries when leaving the product unattended for longer periods of time.
If liquid from the batteries comes into contact with skin or clothing, immediately rinse with fresh water.

Do not use cleaning solvents or abrasives.
Do not attempt to repair the device. If the device does not operate correctly, replace it with a new device.
Clean the outside of the device using a soft, damp cloth.

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Do you have a question about the KN-BM20 and is the answer not in the manual?

Save Article as PDF