Related Manuals for ZAMBELLI AIR-MATIC
Summary of Contents for ZAMBELLI AIR-MATIC
- Page 1 PNEUMATIC CROWN CAPS CORKER AIR-MATIC User and maintenance booklet Via dell’ Artigianato, 70 - 36043 Camisano Vicentino (VI) Italy Tel. 0444/719402 Fax 0444/719423 www.zambellienotech.it - E-mail: info@zambellienotech.it...
-
Page 2: Table Of Contents
INDEX INTRODUCTION _______________________________________________________________ 5 HOW TO READ THIS MANUAL _________________________________________________ 5 1.1.1 Purpose and content of the manual _____________________________________________ 5 1.1.2 General warnings ___________________________________________________________ 5 1.1.3 Preserve the manual _________________________________________________________ 5 MACHINE MANUFACTURER DATA _____________________________________________ 6 TECHNICAL ASSISTANCE _____________________________________________________ 6 WARRANTY ________________________________________________________________ 6 DESCRIPTION _________________________________________________________________ 7 DESCRIPTION OF THE MACHINE ______________________________________________ 7... - Page 3 NAMEPLATE ATTACHED TO THE MACHINE IMPORTANT: THIS BOOKLET IS THE PROPERTY OF ZAMBELLI ENOTECH, ANY REPRODUCTION, EVEN PARTIAL, IS PROHIBITED. TYPE OF DOCUMENT: INSTRUCTION MANUAL AND SPARE PARTS FOR THE FOLLOWING MACHINE: PNEUMATIC CORKER AIR-MATIC EUROPEAN COMMUNITY LEGISLATION Instructions taken from the following have been used in composing this manual:...
- Page 4 EC Declaration of Conformity The undersigned: ZAMBELLI ENOTECH srl Via dell’ Artigianato, 70 36043 – Camisano Vicentino Vicenza (ITALY) Assuming full responsibility, declares that the following machine: AIR-MATIC Type: PNEUMATIC CROWN CAPS CORKER Serial number: n°________ Year of construction: 201__...
-
Page 5: Introduction
HOW TO READ THIS MANUAL 1.1.1 Purpose and content of the manual This manual describes the PNEUMATIC CORKER AIR-MATIC This manual was written to allow machine operators to: know the operational issues related to the machine;... -
Page 6: Machine Manufacturer Data
WARRANTY ZAMBELLI ENOTECH guarantees that the machine was built in compliance with existing norms, in particular those related to the health and safety or workers. The product warranty lasts 12 months; electrical parts are excluded from the warranty. -
Page 7: Description
DESCRIPTION DESCRIPTION OF THE MACHINE Air-Matic is a crown-caps corker for crown caps Ø26 and Ø29 (optional Ø31) and for plastic mushroom corks; it’s adjustable in height, with the possibility to cork bottles of various heights and diameters: Hmin.: 130 mm Hmax: 410 mm Ømin.: 40 mm... -
Page 8: Technical Data Sheet
500 - 600 * approximate value PURPOSE OF USE The corker AIR-MATIC series, is made to corking bottles containing liquids such as wine, oil, juice, milk, etc. All working operations must be carried out by one single operator. It is FORBIDDEN to use the machine for: 1. -
Page 9: Safety
SAFETY GENERAL INFORMATION The aim of the following chapter is to inform operators of possible risks and safety regulations to keep in mind when using the machine. However, such regulations must be respected in any working environment. Each operator must look after their own health and safety and that of other people present at work. In particular, operators must: use the machine correctly following the instructions in the user’s manual;... -
Page 10: Installation And Working
INSTALLATION AND WORKING MOVING AND POSITIONING As first operation, once unpacked the corker, assemble the handle A securing it on the top of the fixed frame D, using the two screws provided with handle, inside the box. Moving happens in sure way appealing the corking machine through the handle A. Once arranged the corking machine on a flat surface, you will proceed to eventual leveling of the frame by adjusting the feet I. -
Page 11: Setting Up
SETTING UP ATTENTION: the protection N must be in vertical position towards down, if it results too much loose, clasp the bolt places on the hinge O. Operating procedure (see FIG. III) 1- position the cap under the bell M. This one remain connected by means of the magnet placed on it; 2- position the bottle to be capped on the support plane H, putting it to the bottle holder L;... -
Page 12: Maintenance
MAINTENANCE ORDINARY MAINTENANCE ACTIVITIES (GENERAL INFORMATION) For good maintenance: use only original spare parts, suitable equipment for the task and in good conditions; respect the frequency of interventions indicated in the manual for programmed maintenance (preventative and periodic); good preventative maintenance requires constant attention and continuous surveillance of the machine. -
Page 13: Spare Parts
SPARE PARTS WARNING: to have the machine operate correctly, it is recommended that original spare parts supplied by the manufacturer are always used. FRAME FIXING KNOB HEAD ADJUSTABLE FOOT PISTON TUBE HANDLE 2/2A PISTON PLATE LOWER HINGE 2/2B PISTON PLATE HIGHER PLEXIGLASS PROTECTION OR PISTON NYLON BUSHING... -
Page 15: Waste Disposal And Demolition
WASTE DISPOSAL AND DEMOLITION WASTE DISPOSAL When using the machine waste materials are generated during processing which must be collected, recycled or disposed of in accordance with the laws that exist in the country where the machine is installed. Machine parts which are substituted must also be handled in the same way.