SAL PIXIE Smart Switch G3 Quick Start Manual

Smart Switch G3
SWL600BTAM

1. Foreword

IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE GUIDE AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation in accordance with AS/NZS3000
DIY
by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the following instructions and SAL
standard terms and conditions of sale, available via www.sal.net.au.
Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance guarantee
unless expressly confirmed in writing by SAL at the time of order.The product wireframe drawings in this document are intended for illustration purposes only and may differ
from the final physical product. The installation instruction is subject to change without prior notice.

2. Product Introduction

PIXIE Smart Switch G3 is the third generation push button smart switch,
that toggles the ON/OFF status of the load via a single press.

2.1 Product Features

• Fits most branded switch plates
• Fits 1 to 6 gang wall plate installation
• Over temperature protection, overload protection, short circuit
protection
• Complies with Australian and New Zealand Standard: AS/NZS
60669.2.1
• Smart functions via phone/tablet with the SAL PIXIE or PIXIE PLUS APP
• Multiway control - When pairing multiple PIXIE multifunction control
device (e.g. SMF/BTAS) with the same smart Switch, multiway-way
control is achieved
• LED indicator illuminates at high brightness when the switch is on, and
faint when the switch is off, allowing the user to identify the button in the
dark
• LED indicator can be enabled and disabled through the Apps

3. Specifications

3.1 Basic specifications

Model No. Input (V)/(Hz)
SWL600BTAM
240/50
*Subject to the load's electrical characteristics, the load may require the inclusion of a load correction capacitor given in the product carton

3.2 Load rating

Resistive load
No. of switch (Incandescent/High voltage
halogen lamp)
600W
1
500W
2
3 500W
300W
4
300W
5
6 200W
Caution/Notice
Loads with poor electrical performance will apply additional destructive impact to the switch, beyond its rated capabilities, irrespective of power consumption. This
can result on both a shortened lifespan and irreversible damage to this device. This device is not compatible with device below this minimum specification.
-Power Factor < 0.7
-In-rush current > 50A

4. Installation and Wiring

Installation process
• Make sure the key cap compatibility (pry and replace the default key
cap if necessary)
• Check the load rating and confirm the load compatibility
*All drawings shown are for illustration purpose only, actual product may vary due
to product enhancement.
Min / Max loads Colour
9*/600W Blue
Inductive load
Capacitive load
(e.g. exhaust
(e.g. LED, CFL)
fan)
400VA 120VA
250VA 100VA
200VA 80VA
150VA 80VA
150VA 60VA
100VA 60VA
• Turn OFF the mains electricity supply before commencing installation
• Connect the switch according to the wiring diagram
• Turn ON the mains electricity supply, wait for 10 seconds, then test the
switch operation by pressing the switch button.
Quick Start Guide

2.2 The package includes

• PIXIE Smart Switch G3 * 1
• Extra key caps * 2
• Silicon spacer * 1

2.3 Product illustration*

Default key cap
(Interchangeable)
Dimension L x W x H (mm)
42 x 24 x 24

3.3 Load compatibility

Compatible Loads
Incandescent lamp
240V halogen lamp
Low voltage halogen with electronic transformer
CFL
LED fixture
M ASTE R
Version 2.0
Date 22/06/2023
• Load correction capacitor * 1
• Quick Start Guide * 1
LED indicator
Wireless
Bluetooth Mesh Technology
Yes
Yes
Yes
Yes
Yes