Summary of Contents for Image Dynamics USA IDQ V4 Series
Page 1
IDQ Series Subwoofers V4 IDQ8V4 D4/D2 IDQ10V4 D4/D2 IDQ12V4 D4/D2 OWNERS MANUAL Please read through this manual to familiarize yourself with your new subwoofer. Should your Image Dynamics subwoofer ever require service, you will need to have the original dated receipt.
Page 2
In the interest of safety, Image Dynamics USA highly recommends listening at lower volume levels when driving.
Page 3
IMAGE DYNAMICS IDQ SERIES SUBWOOFERS High Excursion Design allows acoustically linear bass output at all rated power levels. Parabolic Santoprene Surround to ensure cone linearity andcontrol. Poly Mica Cone for strong distortion free bass reproduction while still reproducing all of the musical nuances.
WIRING GUIDELINES It is highly recommended that you seek an authorized Image Dynamics dealer to properly setup, wire and install your woofers for maximum performance. There are multiple ways to wire your woofers depending on your amplifier and system configuration. The use of multiple voice coils offers you more versatility in system con- figuration.
Page 5
DUAL VOICE COIL WIRING (DUAL 2 OHM) SERIES PARALLEL Parallel wiring a dual 2 ohm sub = 1 ohm Series wiring a dual 2 ohm sub = 4 ohm PARALLEL-PARALLEL SERIES PARALLEL Parallel-Parallel wiring two dual 2 ohm subs = 1/2 ohm Series-Parallel wiring two dual 2 ohm subs = 2 ohm NOTE: Never connect only one coil of a Dual Voice Coil (DVC) speaker.
Page 6
TIPS TO GET THE MOST OUT OF YOUR IMAGE DYNAMICS SUBWOOFERS Your Image Dynamics subwoofer has been meticulously engineered and designed to handle high power musical reproduction. Despite their rugged construction, it is possible to damage your speaker if they are improperly used. In general, you will hear distortion as a so-called warning before any damage occurs.
Page 7
BOX CONSTRUCTION The material used for enclosure walls should be solid, dense and free of voids or warps. Your enclosure should be made ¾” or 19mm material, Finland or Baltic birch type plywood is recommended where the enclosure will be transported frequently. High-density fiberboard - MDF (not chip board) can be used on permanently installed systems.
Page 8
PARAMETERS FOR IDQ SERIES SUBWOOFERS (Due to Constant Improvements, Specifications and Parameters are subject to change without notice.) IDQ8D2 IDQ8D4 IDQ10D2 IDQ10D4 VC Impedance (ohms) 2Ω + 2Ω 4Ω + 4Ω 2Ω + 2Ω 4Ω + 4Ω Test Impedance (ohms) 0.94Ω...
Page 9
PARAMETERS FOR IDQ SERIES SUBWOOFERS (Due to Constant Improvements, Specifications and Parameters are subject to change without notice.) IDQ12D2 IDQ12D4 VC Impedance (ohms) 2Ω + 2Ω 4Ω + 4Ω Test Impedance (ohms) 0.94Ω 1.35Ω Driver Displacement 0.10 cuft. 0.10 cuft. Fs (Hz) SD (sqCM) 510.72...
RECOMMENDED ENCLOSURES Please note that these enclosure volume recommendations are for the internal airspace in- side the enclosure and include the displacement of the subwoofer and ports. When choos- ing your enclosure type, please pay close attention to your specific woofer, failing to use the correct enclosure may result in lower power handling and poor sound quality.
Page 11
IDQ8 Ported Enclosures PORTED ENCLOSURE TYPE Compact Universal Audiophile Gross Vb Internal 0.5 cu.ft 0.75 cu.ft 1.0 cu.ft 40 Hz 40 Hz 40 Hz Port Frequency 37 Hz 34 Hz 32 Hz F3 (-3dB Cutoff) Port Dimensions 2" x 9" 2"...
Removed or altered serial numbers will void this warranty This manual is the exclusive property of Image Dynamics USA, Inc. Any reproduction of this manual, or use other than its inten- tions is strictly prohibited without the express consent of Image Dynamics USA, Inc. Copyright 2023 Image Dynamics USA, Inc.
Page 16
Image Dynamics USA 2133 S. Green Privado – Ontario, CA 91761 Tel. (909) 930-1377 – Fax (866) 239-4399 www.imagedynamicsusa.net...
Need help?
Do you have a question about the IDQ V4 Series and is the answer not in the manual?
Questions and answers