Advertisement
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNPACKING AND CHECKING EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARATION OF DESK TOP STATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARATION OF MOBILE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE MOBILE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE DESK TOP STATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE STANDBY POWER TRANSFER OPTION . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE REMOTE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE REMOTE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE KEYPAD BOARD OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE CLOCK/VU MODULE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMING NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION INSTRUCTIONS (MDX RADIO APPLICATION) . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION INSTRUCTIONS (ORION RADIO APPLICATION) . . . . . . . . . . . . . . . . . . . . . . . .
INTERCONNECTION DIAGRAM (MDX RADIO APPLICATION) . . . . . . . . . . . . . . . . . . . . . . . . .
INTERCONNECTION DIAGRAM (ORION RADIO APPLICATION) . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION
This manual contains instructions for the assembly of a
Desk Top Station. This is done by installing an MDX mobile or
ORION mobile radio into the Desk Top Station Assembly, us-
ing the hardware kit supplied.
Mobile radios which can be accommodated by the Desk
Top Station are all MDX radios and ORION up to the mid
transmitter power levels. Only the local control version station
is available for the ORION mobile.
Included are mounting instructions for the radio, as well as
instructions for making the few required cable connections. In-
stallation is made easy with the help of an Installation Diagram
and an Interconnection Diagram, included as part of this man-
ual.
UNPACKING AND CHECKING
EQUIPMENT
Hardware Kit 349A9561 was used to assemble your sta-
tion. The unused material was shipped with the station. Re-
move the kit and store for possible use.
Copyright© September 1993, Ericsson GE Mobile Communications Inc.
DIAGRAMS
Installation of the Desk Top Station includes three parts:
1.
Installation of the Mobile Radio in the Desk Top Sta-
tion Assembly using Hardware Kit 349A9561 (sup-
plied).
2.
Installation of Option Boards in the Desk Top Station
Assembly, in accordance with options selected. Re-
mote Interface Board Option, with one of the follow-
ing remote boards:
a.
DC Remote Board
b.
4-Channel Tone Remote Board
c.
5-Channel EDACS Tone Remote Board
d.
Standby Power Transfer Option
e.
Clock/VU Meter Option
3.
Installation of the Desk Top Station in the place of op-
eration with the necessary power, antenna, micro-
phone, and line connections.
INSTALLATION
Page
PREPARATION OF DESK TOP STATION
1
1.
Loosen the two (2) captive screws which hold the
1
top cover on the Desk Top Assembly. Remove the
1
cover.
1
2.
Disconnect cable W2 from J202 on the Interconnect
1
board and also from J215 (ORION Application).
1
3.
Loosen, Do Not Remove, the two (2) M3.5 screws
1
that hold the radio mounting bracket on the Desk
2
Top Station Assembly.
2
4.
When external wires for options are to be con-
2
nected, remove and discard the round knockout but-
2
ton in the rear of the station housing. Insert the
3
rubber grommet 5490407P10 in the hole. Place the
3
cable clamp (344A3480P1) around the wires. Snap
the cable clamp retainer into the hole adjacent to
the grommet.
4
PREPARATION OF MOBILE RADIO
16
17
MDX Radio
20
1.
Remove the bottom cover of the radio by removing
®
the four (4) retaining TORX
2.
Unplug the radio internal speaker cable from J904
on the radio and let it hang.
3.
Discard the rubber plug and in its place slip the rub-
ber sleeve on cable W2. P905 of W2 plugs into
J905.
4.
Replace the bottom cover of the radio with the four
®
(4) retaining TORX
screws removed in Step 1.
5.
Using a permanent marker, copy the FCC identifi-
cation number of the radio onto the Desk Top Sta-
tion FCC label.
6.
Attach the side mounting brackets with four (4) hex
mounting screws and four (4) washers (2 per side)
in the sides of the radio.
ORION Radio
1)
No special modifications required.
2)
Attach the side mounting brackets with four (4) hex
mounting screws (2 per side) in the sides of the ra-
dio.
INSTALLING THE MOBILE RADIO
1.
Connect P202 of cable W2 from the radio to J202
on the Interconnect Board. Also connect P215 to
J215 when ORION radio is used.
2.
Connect P101 of the Desk Top Station antenna ca-
ble W1 into the RF TNC connector on the radio.
3.
Power Cable Connections:
a.
MDX - Connect P1 of the Desk Top Assembly
power cable W3 to J1 of the radio power cable
W901.
b.
ORION USA Version - Connect P1 of Desk
Top Assembly power cable W3 to J1002 on the
rear of the radio unit.
c.
ORION European Version - There is no cable
W3. The power connections are included in ca-
ble W2 which connects to the DB37 connector
on the radio unit.
4.
Place the radio in the mounting bracket and posi-
tion it for the proper Desk Top Station front appear-
ance and tighten the two (2) M3.5 screws that hold
the radio mounting bracket in place.
5.
Replace the Desk Top Assembly cover using the
screws.
two (2) screws loosened in Step 1 of "PREPARA-
TION OF DESK TOP STATION."
This completes the installation of the mobile radio in the
Desk Top Station Assembly.
INSTALLING THE DESK TOP STATION
AC Power
The Desk Top Station power supply must be connected
to AC power with the fused and ON/OFF-switched AC
power cable found at the back of the Desk Top Assembly.
The transformer straps are shipped set for a 120 volt power
source:
120volts ±10%, Single-Phase, 50/60 Hz, 4 amps,
500 watts
Refer to Power Supply Maintenance Manual LBI-38751
for procedures to change the transformer straps to accommo-
date a 240 volt power source:
240volts ±10%, Single-Phase, 50/60 Hz, 2 amps,
500 watts
Different Desk Top Station power supplies may have dif-
ferent current capabilities. Refer to the applicable power su-
ply maintenance manual for current usage.
LBI-38977
1
Advertisement
