Advertisement
Available languages
Available languages
Quick Links
The TCELL940 and TCELL940-W are cells designed for pools up to 40,000 gallons. When replacing an existing T-CELL-15, GLX-CELL-15,
or TCELL940, no re-configuration is necessary.
If configuration is required, refer to the information below. Incorrect configuration will cause inaccurate salt readings, improper operation,
and possible system shutdown.
CONFIGURATION is necessary with the following models:
•
AQR (Aqua Rite - all 2009 or later) - firmware version 1.5 or later
•
AQR-PRO (Aqua Rite Pro)
•
OmniLogic & OmniPL - refer to owner's manual for configuration
•
PL-P-4 (Pro Logic P4)
•
PL-PS-x (Pro Logic PS)
•
AQ-LOGIC-P-4 (Pro Logic P4)
•
AQ-LOGIC-PS-x (Pro Logic PS)
•
AQR900 series - all
NO CONFIGURATION is necessary with the following models:
•
AQ-RITE (Aqua Rite - 2008 and earlier) - firmware earlier than version 1.5
•
AQ-RITE-XL (Aqua Rite XL)
Connecting to an AQR or AQR900:
1. Slide the Main Switch to the "Auto" position.
2. Push the Diagnostic button repeatedly until "t-xx" appears on the display ("t-15" is the factory default). If "t-15" is displayed, skip to
step 4.
3. To change cell type, slide the Main Switch from "Auto" to "Super Chlorinate" and back to "Auto". Repeat this process until the "t-15" is
displayed.
4. Push the Diagnostic button to exit.
Connecting to an AQR-PRO:
1. Access the Settings Menu by pushing the "Settings" button.
2. Push ">" until Chlor. Config is displayed, then push "+".
3. Push ">" repeatedly until "Cell Type" is displayed.
4. Push "+" or "-" until "T-CELL-15" is displayed.
5. Exit Settings Menu by pushing the "Info" button.
Connecting to an AQ-LOGIC-P-4, AQ-LOGIC-PS-x, PL-P-4 or PL-PS-x:
1. Enter the Configuration Menu.
2. Push ">" until Chlor. Config is displayed, then push "+".
3. With the Chlorinator Enabled, push ">" repeatedly until "Cell Type" is displayed.
4. Push "+" or "-" until "T-CELL-15" is displayed.
5. Exit Settings Menu by pushing the "Menu" button.
TCELL940
TCELL940-W
MENU SETTING MAY BE REQUIRED!
Hayward Industries
400 Connell Drive, Suite 6100
Berkeley Heights, NJ 07922
Phone: (908) 355-7995
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
092625 RevC
Advertisement
Related Manuals for Hayward TCELL940
Summary of Contents for Hayward TCELL940
- Page 1 TCELL940-W MENU SETTING MAY BE REQUIRED! The TCELL940 and TCELL940-W are cells designed for pools up to 40,000 gallons. When replacing an existing T-CELL-15, GLX-CELL-15, or TCELL940, no re-configuration is necessary. If configuration is required, refer to the information below. Incorrect configuration will cause inaccurate salt readings, improper operation, and possible system shutdown.
- Page 2 As a precaution, the cell can be installed vertically or in an inverted manner (see illustration) to keep it flooded with water. Inverted Installation Vertical Installation Desired installation configurations when using 2 speed or variable speed pumps. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
- Page 3 DE NOUVEAUX RÉGLAGES PEUVENT ÊTRE NÉCESSAIRES! Les TCELL940 et TCELL940-W sont des cellules à conçues pour les piscines d’un volume maximum de 151 416 L (40 000 gal). Lorsque vous remplacez une cellule existante de type T-CELL-15, GLX-CELL-15 ou TCELL940-CUL, une reconfiguration n’est pas nécessaire.
- Page 4 Hayward is a registered trademark and AquaRite, ProLogic and OmniLogic are trademarks of Hayward Industries, Inc. © 2022 Hayward Industries, Inc. All other trademarks not owned by Hayward are the property of their respective owners. Hayward is not in any way affiliated with or endorsed by those third parties.