en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Safety en 1.4 Safe installation WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Connect the appliance to a power supply with alternating cur- rent only via a properly installed socket with earthing. ▶...
Page 6
en Safety WARNING ‒ Risk of injury! The high weight of the appliance may result in injury when lifted. ▶ Do not lift the appliance on your own. If this appliance is not correctly installed in a washer-dryer stack, the installed appliance may fall. ▶...
Safety en ▶ Wear protective gloves when installing and transporting the ap- pliance. 1.5 Safe use WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. ▶ Never operate a damaged appliance. ▶ Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
Page 8
en Safety WARNING ‒ Risk of poisoning! Detergents and care products may result in poisoning if con- sumed. ▶ If accidentally swallowed, seek medical advice. ▶ Keep detergents and care products out of the reach of children. WARNING ‒ Risk of explosion! Laundry that has been pretreated with cleaning agents that con- tain solvents may cause an explosion in the appliance.
Safety en 1.6 Safe cleaning and maintenance WARNING ‒ Risk of electric shock! Incorrect repairs are dangerous. ▶ Repairs to the appliance should only be carried out by trained specialist staff. ▶ Only use genuine spare parts when repairing the appliance. ▶ If the power cord of this appliance is damaged, it must be re- placed by the manufacturer, the manufacturer's Customer Ser- vice or a similarly qualified person in order to prevent any risk.
en Preventing material damage If the water pressure is too high or Preventing material damage 2 Preventing material too low, the appliance may not be able to operate properly. damage Ensure that the water pressure in ▶ the water supply system is at least Preventing material damage ATTENTION! 100 kPa (1 bar) and max.
Environmental protection and saving energy en Set the maximum spin speed if you Environmental protection and saving energy 3 Environmental protec- want to dry the laundry in the tumble tion and saving energy dryer afterwards. a The drier the laundry, the shorter Environmental protection and saving energy the programme duration when dry- 3.1 Disposing of packaging...
en Installation and connection Replace the accessories in ques- ▶ Installation and connection 4 Installation and con- tion before operating the appli- ance. nection → "Accessories", Page 27 Installation and connection Note: The appliance has been tested 4.1 Unpacking the appliance at the factory to check it is in working order.
Page 13
Installation and connection en ATTENTION! Installation loca- Requirements If residual water in the appliance tion freezes, this may cause damage to Against a wall Do not trap the the appliance. power cord or Do not install or operate this appli- ▶ the hoses ance anywhere that is liable to ex- between the wall...
en Installation and connection Unscrew and remove all of Put on the 4 cover caps. the screws for the 4 transit bolts using a WAF 13 wrench. Push the 4 cover caps downwards. Remove the power cable from the holder. Note: To install the transit bolts to transport the appliance, perform these steps again in the reverse or- Remove the 4 sleeves.
Page 15
Installation and connection en Connect the water inlet hose to a Plastic pipe with Fix and secure tap (26.4 mm = 3/4"). rubber sleeve or the water outlet gully hose with an el- bow. → "Accessories", Page 27 Connecting the appliance to the electricity supply Note: Your electrical domestic install- ation for this appliance must comply Open the water tap carefully and with the local legal provisions and...
en Installation and connection Use a WAF 17 wrench to tighten 4.6 Aligning the appliance the lock nuts against the housing In order to reduce noise and vibra- until they are hand-tight. tion and to prevent the appliance from moving, align the appliance cor- rectly.
Familiarising yourself with your appliance en Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. On certain models, specific details such as the colour and shape may differ from those pictured.
en Familiarising yourself with your appliance Measuring aid for liquid deter- gent → "Inserting the measuring aid for liquid detergent", Page 28 Dispenser II: detergent for the main wash Compartment : Fabric softener Compartment I: Detergent for prewash 5.3 Control panel You can use the control panel to configure all functions of your appliance and to obtain information about the operating status.
Before using for the first time en Add washing powder that contains Before using for the first time 6 Before using for the a bleaching agent to compart- ment II. first time Prepare the appliance for use. Before using for the first time 6.1 Starting an empty wash- ing cycle Your appliance was inspected thor-...
en Display Display 7 Display The display shows the current settings, options or relevant information. Display Example: Display Display Description 0:40 Expected programme duration or programme time re- maining in hours and minutes. Program end time → "Buttons", Page 22 Recommendation for the maximum load capacity for the selected program in kg.
Page 21
Display en Display Description Wash Programme status Rinse Programme status Spin Programme status Program end Programme status ¡ Lights up: The childproof lock is activated. ¡ Flashes: The childproof lock is activated and the appli- ance has been operated. → "Deactivating the childproof lock", Page 31 The crease-reduction function is activated.
en Buttons Buttons 8 Buttons The selection of programme settings depends on the programme that is set. Buttons Button Selection More information Start / Reload ¡ Start Start, cancel or pause the pro- gramme. ¡ Cancel ¡ Pause Speed Perfect ¡ Activate Activate or deactivate a shorter pro- gramme duration.
Programmes en Programmes 9 Programmes Programmes Note: The laundry's care labels provide you with additional information on pro- gramme selection. Programme Description Max. load (kg) Cottons Wash hard-wearing items made of cotton, linen or blended fabrics. Also suitable as a short programme for normally soiled laundry when you activate Speed Perfect.
Page 24
en Programmes Programme Description Max. load (kg) Easy Care Wash items made from synthetic or blended fab- rics. Programme setting: ¡ Max. 60 °C ¡ Max. 1200 rpm Mixed Load Wash items made from cotton, linen, or synthetic or blended fabrics. Suitable for lightly soiled laundry.
Page 25
Programmes en Programme Description Max. load (kg) Note: Once the set temperature has been reached, it remains constant throughout the entire washing process. Programme setting: ¡ Max. 60 °C ¡ Max. 1400 rpm Sportswear Wash sports and leisure items made from synthetic fibres, microfibre or fleece. Use a detergent that is suitable for sports items.
en Programmes Programme Description Max. load (kg) Super Quick Wash items made from cotton, or synthetic or blen- 15'/30'' ded fabrics. Short programme for small items of lightly soiled laundry. The programme duration is approx. 30 minutes. If you wish to reduce the programme duration to 15 minutes, activate Speed Perfect.
Accessories en Accessories 10 Accessories Use original accessories. These have Accessories been made especially for your appli- ance. Note: Some accessories are avail- able in other colours. Contact → "Customer Service", Page 48. Order num- Water inlet hose ex- Extend the water inlet hose for cold water WMZ2381 tension or AquaStop (approx.
en Detergents and care products If required, adjust the programme Detergents and care products 12 Detergents and care settings. → "Adjusting the programme set- products tings", Page 28 The manufacturer's instructions for Detergents and care products use and dosage can be found on the 13.3 Adjusting the pro- packaging.
Basic operation en Press down on the insert and re- Slide the measuring aid forwards. move the detergent drawer. Fold the measuring aid down and Insert the measuring aid. click it into place. Insert the detergent drawer. Push in the detergent drawer. 13.6 Use the measuring aid 13.7 Adding detergent and for liquid detergent...
en Basic operation Remove the laundry. 13.8 Starting the programme → "Unloading the laundry", Requirement: A programme is set. Page 30 → "Setting a programme", Page 28 13.11 Resuming the pro- Press Start / Reload. ▶ gramme when the pro- a The drum rotates and load detec- tion takes place. This can take up gramme status is Rinse to 2 minutes, after which water Hold...
Childproof lock en Leave the appliance door and de- tergent drawer open so that resid- ual water can evaporate. Childproof lock 14 Childproof lock Secure your appliance against being Childproof lock operated unintentionally using the controls. 14.1 Activating the childproof lock Press and hold the two ...
en Basic settings Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 15.1 Overview of the basic settings Basic setting Programme Value Description position End signal 0 (off) Set the volume of the signal at the 1 (quiet) end of the programme.
Cleaning and servicing en 15.2 Changing the basic set- Cleaning and servicing 16 Cleaning and servi- tings cing Set the programme selector to po- To keep your appliance working effi- sition 1. Cleaning and servicing ciently for a long time, it is important to clean and maintain it carefully.
en Cleaning and servicing Press down on the insert and re- Fit the insert and click it into place. move the detergent drawer. Clean the opening for the deter- Pull out the insert upwards. gent drawer. Clean the detergent drawer and in- Push in the detergent drawer.
Page 35
Cleaning and servicing en Open and remove the mainten- CAUTION - Risk of scalding! ance flap. When you wash at high temperat- ures, the detergent solution gets hot. Do not touch the hot detergent ▶ solution. To allow the detergent solution to flow out into the container, remove the sealing cap.
Page 36
en Cleaning and servicing Insert the pump cap. Cleaning the drain pump Ensure that the parts of the Requirement: The drain pump is ‒ pump cap are correctly as- empty. → Page 34 sembled. Since water may remain in the drain pump, unscrew the pump cap carefully.
Page 37
Cleaning and servicing en Before the next wash To prevent unused detergent from flowing straight into the outlet in the next wash, run a suitable programme for draining after you have emptied the drain pump. Open the water tap. Insert the mains plug. Switch on the appliance.
en Troubleshooting Troubleshooting 17 Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Improper repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶...
Page 39
Troubleshooting en Fault Cause and troubleshooting "E:30 / -80" Immediate measure: Mix one tablespoon of fabric ▶ softener with 0.5 litres of water and pour the mix- ture into compartment II (not for outdoor clothing, sportswear or items stuffed with down). Reduce the amount of detergent for the next wash- ▶...
Page 40
en Troubleshooting Fault Cause and troubleshooting lights up. The temperature is too high. Wait until the temperature has dropped. ▶ → "Cancelling the programme", Page 30 ▶ Water level is too high. Select a suitable programme for draining. ▶ → "Programmes", Page 23 flashes. Door is not closed. Close the door.
Page 41
Troubleshooting en Fault Cause and troubleshooting The programme does You have not pressed Start / Reload. not start. Press Start / Reload. ▶ Door is not closed. Close the door. ▶ Childproof lock is activated. Deactivate childproof lock. ▶ → "Deactivating the childproof lock", Page 31 Finish in is activated.
Page 42
en Troubleshooting Fault Cause and troubleshooting The water is not drain- Reduce the amount of detergent for the next wash- ▶ ing. ing cycle with the same load. Unapproved extension installed on the water drain hose. Remove any unapproved extensions from the water ▶...
Page 43
Troubleshooting en Fault Cause and troubleshooting No water is visible in Water is below the visible area. the drum. Not a fault – no action required. ▶ Do not add any extra water to the appliance while it ▶ is operating. Drum jerks after the This is caused by an internal motor test.
Page 44
en Troubleshooting Fault Cause and troubleshooting The spin programme Drain pipe or water outlet hose is blocked. does not start. Clean the drain pipe and the water outlet hose. ▶ Drain pipe or water drain hose is caught or jammed. Ensure that the drain pipe and water drain hose are ▶...
Page 45
Troubleshooting en Fault Cause and troubleshooting Detergent or fabric Too much detergent/fabric softener in the detergent softener drips off the drawer. seal and collects on When dosing liquid detergent and fabric softener, ▶ the door or in the seal observe the marking in the detergent drawer and fold.
Page 46
en Troubleshooting Fault Cause and troubleshooting Water is leaking out at Water inlet hose is not correctly/securely connected. the water inlet hose. Connect the water supply hose correctly. → "Connecting the water inlet hose", Page 14 Tighten the screw connection. Water is leaking out at The water outlet hose is damaged.
Transportation, storage and disposal en 17.1 Emergency release 18.2 Inserting the transit bolts Releasing the door Secure the appliance before trans- Requirement: The drain pump is portation using transit bolts in order empty. → Page 34 to prevent transport damage. ATTENTION! Escaping water may Use a screwdriver to remove the 4 cause material damage.
en Customer Service 18.4 Disposing of old appli- Customer Service 19 Customer Service ance Function-relevant genuine spare parts Customer Service Valuable raw materials can be re- according to the corresponding Eco- used by recycling. design Order can be obtained from Customer Service for a period of at WARNING least 10 years from the date on Risk of harm to health!
Consumption values en Consumption values 20 Consumption values The following information is provided in accordance with the EU Ecodesign Consumption values Regulation. The values given for programs other than the Eco 40-60 are indicat- ive only and were determined in accordance with the applicable standard EN60456.
Page 50
en Technical data Mains voltage 220-240 V, 50-60 Hz Minimum in- 10 A stallation protec- tion Nominal power 2300 W Power consump- ¡ Off mode: tion 0.15 W ¡ Left-on mode: 0.50 W Water pressure ¡ Minimum: 100 kPa (1 bar) ¡ Maximum: 1000 kPa (10 bar) Length of the wa- 150 cm ter inlet hose Length of the wa-...
Page 52
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.