Download
Share
Print this page
ABB XIO X Series Installation Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Antenna
  5. XIO X Series
  6. Installation manual
ABB XIO X Series Installation Manual

ABB XIO X Series Installation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
A B B M E A S U R E M E N T & A N A LY T I C S | I N S TA L L A T I O N G U I D E
Wi-Fi
Antenna Kit
®
XIO, XSeries
Introduction
This document defines the procedures and list the parts required to
install a Wi-Fi antenna.
IMPORTANT NOTE: To enable and configure Wi-Fi for secure
access, refer to the XSeries
manuals.
G5
(XFC or XRC) or the XIO user
G5
Secure and easy wireless access
for configuration.
Measurement made easy

Advertisement

loading

Related Manuals for ABB XIO X Series

Summary of Contents for ABB XIO X Series

  • Page 1 A B B M E A S U R E M E N T & A N A LY T I C S | I N S TA L L A T I O N G U I D E Wi-Fi Antenna Kit ®...

  • Page 2: Additional Information

    ABB Inc. and its affiliates are not liable for damages and/or losses related to such security breaches, any unauthorized access, interference, intrusion, leakage and/or theft of data or information.

  • Page 3: Potential Safety Hazards

    Safety Observe warning signs on packaging and on the devices, prior to software configuration. Potential safety hazards WARNING – Bodily injury: Make sure no explosive atmosphere is present before connecting or disconnecting any connector or performing maintenance on this unit. WARNING –...

  • Page 4: Installation Procedures

    XSeries and XIO enclosures vary in size. Order the antenna kit option which includes the cable length appropriate for your enclosure: Table 1-2: Kit options per cable length Kit number Cable length ABB Enclosure 2106049-501 24 inches 6410 2106049-502 32 inches...
  • Page 5 Attach the right angle SMA fitting of the cable to the board ANT-1, connector (J42). Figure 3: Attach at ANT-1 Attach the plug-to-jack Attach the surge protector adapter to the straight SMA to the plug-to-jack adapter. fitting of the cable. Figure 4: Attach the straight Figure 5: Attach the surge SMA fitting...
  • Page 6 Figure 6: Crimp ring terminal Crimp the surge protector terminal ring to the ground cable. Re-attach the crimped terminal with ground cable to the surge protector. Attach the cable to the surge protector (see below). Figure 7: Attach the cable Remove the split washer and hex nut from the surge protector.
  • Page 7 ABB Enclosure Antenna hole Photo of enclosure number location 6410 On the left side of the enclosure, in the upper left corner. 6413 On the bottom of the enclosure, in the back left corner 6890 2 holes are on the...
  • Page 8 View of the installed surge protector from the inside of the enclosure (see below). ABB enclosure 6413 is shown. Figure 9: Inside the enclosure Attach the ground cable to the ground post (see number 2 in the picture below).
  • Page 9 Figure 10: Cable assembly Description Mountable cable ties Ground cable Enclosure ground post Attach the FCC transmission compliance tag to the outside of the enclosure (see below). Figure 11: FCC compliance tag Remove the red protective cap from the surge protector. Attach the antenna to the surge protector.
  • Page 10 Figure 12: Straight antenna Attach the terminator plug to the board ANT-2 (J43) connector (see number 1, below). Figure 13: ANT-2 terminator plug The Wi-Fi antenna installation is complete. 10 | WI-FI ANTENNA KIT | 2106123MNAD...
  • Page 11 We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.