Related Manuals for Perenio PEHWE20
Summary of Contents for Perenio PEHWE20
- Page 1 Perenio® PEHWE20 Two-Channel Mini Relay Installation and Operation Manual May, 2023...
-
Page 3: Introduction
Perenio Smart Home & Office app (hereinafter referred to as the Perenio Smart) to monitor and control the energy consumption of light sources. The Mini Relay is designed to operate inside a sub-socket, under a switch, or in another location suitable for power control. -
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and to make additions and changes to this document without prior notice and shall not be liable for possible negative... -
Page 5: Conformity To Standards
BG CH CZ DK EE appropriate section of the website at perenio.com. GR HR HU IE MT NL NO PL RO RS ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 5 of 50... -
Page 6: Limitations And Warnings
Do not connect the device to equipment that exceeds the specified maximum load. The device may be connected only as specified in the User Manual. Any other method of connection may result in damage and/or injury. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 6 of 50... - Page 7 Do not allow children to use the device without adult supervision and/or play with it. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 7 of 50...
-
Page 8: Table Of Contents
1.4 Packaging and labeling ................15 2 Installation and Setup ................16 2.1 Installation of the Mini Relay..............16 2.2 Activation in the Perenio Smart Mobile App ..........19 2.3 Additional Mini Relay Settings ..............23 2.4 Mini Relay Control Panel ................25 2.4.1 Setting the Countdown Timer ............ - Page 9 VI Creating a scenario from a template ............36 VII Test run of the scenario ................36 VIII Adding a scenario to Favorites ..............37 IX Deleting a scenario ..................37 ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 9 of 50...
-
Page 10: General Description And Specifications
Conventional (with a fixed position); • Pulse (bell). Two control modes are available for each switch type via the Perenio Smart app. To operate the Mini Relay, the following is required: • Smartphone with Internet access and the Perenio Smart app installed;... -
Page 11: Figure 1 - Appearance
It is required for normal operation of the Relay with some types of loads, e.g. when using LED lamps of low power ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 11 of 50... - Page 12 Press and hold for 10 seconds Starting the factory reset process WARNING! All Perenio IoT products and the mobile application (including any further proprietary or third-party software and hardware) are not intended for a rapid response to emergency situations and may not be used as a means of...
-
Page 13: Technical Specification
Permissible cross-section of the wire 2.5 mm to be connected Temperature 0...+50 °C Humidity 5-75 % (no condensation) Storage Conditions Temperature 20...+60 °C Humidity 5-95 % (no condensation) ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 13 of 50... -
Page 14: Package Contents
3. Quick Start Guide (1 pc.) 4. Warranty Card (1 pc.) Figure 2 – Package Contents * * The images of accessories are for reference purposes only. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 14 of 50... -
Page 15: Packaging And Labeling
Installation and Operation Manual 1.4 Packaging and labeling The Perenio® PEHWE20 Mini Relay is supplied in an individual cardboard package measuring 95×50×30 mm (L×W×H), containing the full name and marking, list of supplied devices and accessories, main technical specifications, as well as date of manufacture and manufacturer's information. -
Page 16: Installation And Setup
1. Make sure that the Perenio® Control Gateway or IoT Router is pre-installed, connected to the Internet and activated in the Perenio Smart mobile app. 2. Unpack the Mini Relay. 3. Disconnect the power at the connection point. 4. Make the connection according to one of the 6 diagrams shown in the figure below. - Page 17 Connecting the device to a single pushbutton switch: Connecting the device to a single bell switch: Connection of the device to two pushbutton switches (bypass installed on the first line): ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 17 of 50...
-
Page 18: Figure 4 - Wiring Diagrams
Connection of the device to two pushbutton switches (bypass installed on the second line): Connection of the device to two bell switches (bypass installed on the second line): Figure 4 – Wiring diagrams Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 18 of 50... -
Page 19: Activation In The Perenio Smart Mobile App
Activation in the Perenio Smart Mobile App To connect the Mini Relay via the Perenio Smart app, please follow the below steps: 1. Unpack the device and install it according to par. 2.1 above. - Page 20 “On” position. NOTE. If the Relay is connected to a non-latching switch, you have to press the last one 5 times in 10 seconds. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 20 of 50...
- Page 21 NOTE. To clear connection errors, follow the instructions on your smartphone's screen. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 21 of 50...
-
Page 22: Figure 5 - Process Of Adding A New Device (Mini Relay)
You can view the whole process of connecting Mini Relays in the mobile app in the diagram below. – Process of adding a new device (Mini Relay) Figure 5 Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 22 of 50... -
Page 23: Additional Mini Relay Settings
Perenio® PEHWE20 Two-Channel Mini Relay Installation and Operation Manual Additional Mini Relay Settings Once the device has been activated in the Perenio Smart app, the user can remotely make additional settings for the device. There are two ways to open the settings screen:... - Page 24 • Select which channel (or channels) to be used; • Remove the device from the Room or the user's account; • Find out the current firmware version of the device. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 24 of 50...
-
Page 25: Mini Relay Control Panel
By default, the timer is in the off state. When the timer is launched, the on/off time of the selected channel of the device will be displayed in parentheses. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 25 of 50... -
Page 26: Setting The Scheduled Timer
You can select both channels at once. 2. Select “Turn on” power. 3. Select the time to turn on the Mini Relay. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 26 of 50... - Page 27 NOTE. If you make changes to the activated timer, it will be automatically disabled. A maximum of eight (8) scheduled timers can be activated at the same time. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 27 of 50...
-
Page 28: Setting The Scheduled Timer To Turn Off The Mini Relay
3. Select the turn off time-of the Mini Relay. 4. Activate and select the turn-on time for the Mini Relay. NOTE. It is not obligatory to activate the turn-on time. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 28 of 50... -
Page 29: Deleting The Scheduled Timer
To delete a timer, swipe it from left to right in the “Scheduled Timer” tab and click on the trash can icon. NOTE. You can only delete a timer that is not launched. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 29 of 50... -
Page 30: Creating Scenarios With The Device
4. Enter the desired scenario name. 5. In the “SCENARION TRIGGER” section, click on “Add”. 6. Choose one of the following three types of actions: Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 30 of 50... - Page 31 8. Click the “Save” button. The created scenario will be displayed in the list of scenarios. 9. Launch the scenario by clicking the appropriate button in the “Scenario” tab. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 31 of 50...
-
Page 32: Creating An Automatically Launched Scenario
15 minutes. Scenario implementation shall be as follows: V Creating an automatically launched scenario 1. In the Mini Relay control panel, select “Device Scenario”. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 32 of 50... - Page 33 9. Create a bounding condition similar to step 6 above. 10. In the "ACTION" block, click on "Add". ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 33 of 50...
- Page 34 15 minutes is selected). NOTE. A scenario for which a delay is selected must contain at least one additional action. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 34 of 50...
- Page 35 14. Click the “Save” button. The created scenario will be displayed in the list of scenarios. 15. Run the scenario by clicking the appropriate button in the “Scenarios” tab. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 35 of 50...
-
Page 36: Creating A Scenario From A Template
To activate this feature, you should click on the settings icon in the upper right corner of the scenario control panel and select “Test run”. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 36 of 50... -
Page 37: Adding A Scenario To Favorites
“Delete” and confirm the action. NOTE. A deleted scenario cannot be restored, so if it is accidentally deleted, it must be created again. ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 37 of 50... -
Page 38: History Of Events
CG/IoT Router is required) as follows: a. Sign in to the Perenio Smart app and select the Location where the Mini Relay device is activated; b. In the Devices tab, select the required Mini Relay device from the list and click on the icon (Settings);... -
Page 39: History And Push Notifications
2.6 History and push notifications All notifications and other messages including changes in the status of Perenio® devices are displayed in the “History” tab. The most important messages can be viewed online in the “... - Page 40 Typical Events. Various Perenio IoT newsletters, as well as messages about triggering Door & Window/Motion sensor in the disarmed mode. Standard events. Various news and other information from Perenio IoT, as well as alerts from both the Door&Window Sensor and the Motion Sensor when in the Disarmed mode.
-
Page 41: Maintenance And Repair
In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device. For details on the replacement and repairs of the Perenio® Mini Relay device, please contact your local Company representative or the Tech Support Department at perenio.com. -
Page 42: Warranty Obligations
If the date of sale cannot be determined, the warranty period is calculated from the date of manufacture of the device. Perenio® products are covered under warranty in the form of repair or replacement, depending on the product category. This warranty covers the cost of replacement parts and labor to restore the product to full working order. - Page 43 Limitation of liability Perenio IoT spol s r.o. reserves the right to refuse the warranty service in case of disputable circumstances. Perenio also has the right to make the final decision as to whether an item can be repaired under warranty.
- Page 44 Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 44 of 50...
-
Page 45: Storage, Transportation And Disposal
Installation and Operation Manual 5 Storage, transportation and disposal The Perenio® Mini Relay device may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture. -
Page 46: Other Information
RoHS Declaration of Conformity dated 08.02.2023 Declarations CE Declaration of Conformity dated 08.02.2023 Addresses of Service Centers are available at perenio.com in the ‘Support’ Section. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved Page 46 of 50... -
Page 47: Troubleshooting
Gateway / IoT Router within the mains network signal coverage area of the Relay antenna (up to 30 m indoors, up to 100 m in free space) ©Perenio IoT spol s r.o. All rights reserved Document version: 1.0.3 Page 47 of 50... -
Page 48: Glossary
Dry Contact A contact that is isolated from the control circuit and has no voltage of its own on the terminals. Perenio Smart Software developed by Perenio IoT for remote device Home & Office management. Document version: 1.0.3 ©Perenio IoT spol s r.o. All rights reserved...