Page 2
Notice The illustrations in this user’s manual are for reference only. Actual product specifications may vary with territories. The information in this user’s manual is subject to change without notice. THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF THIS MANUAL.
1. Preface 1.1 Regulations information FCC rules This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1.3 Safety instructions The following safety precautions will increase the life of the PPC (Panel PC). Follow all Precautions and instructions. Do not place this device underneath heavy loads or in an unstable position. Do not use or expose this device around magnetic fields as magnetic interference may affect the performance of the device.
1.4 Explanation of symbols On the device, you may find the following symbols (nonrestrictive list): Indicates the device meets the requirements of the applicable EC directives/regulations. Indicates compliance with Part 18 of the FCC rules. US NRTL_cTUVus List mark Consult the Instructions For Use Caution Indicates this device must not be thrown in the trash but must be recycled, according to the European WEEE (Waste Electrical and...
1.5 Rechargeable Coin Cell Replacement Notice 1. Hazardous situation might develop by the incorrect polarity connection or replacement of a coin cell on the desired Control PCBA. 2. For Coin cell intended to be changed only by Service personnel with the use of soldering.
1.7 Model definition 1. WMP2157 is Panel PC which regarded as Medical Device Data Systems (MDDS). It is a hardware product that transfer, store, convert formats, and display medical device data. These products do not modify the data or modify the display of the data, and it does not by itself control the functions or parameters of any other medical device.
2. Getting to know the basics 2.1 Product specification This User’s Manual provides instructions and illustrations on how to operate this PPC. It is recommended to read this manual carefully before using this PPC. Physical characteristic Dimension 543 x 334 x 49.9 mm Weight 7.6~8 kg (Net) (Depend upon the actually shipping product)
Page 11
Memory DDR4 Support DDR4 memory, RAM socket x2 Speed: 2400MHz, maximun memory size 32GB Power AC adapter 90 watts, 3 pin (FSP GROUP/ FSP090-RBBM1) CAUTION! MODEL WMP2157 IS DESIGNED TO USE WITH THE DC INPUT: (19Vdc / 4.74A) ADAPTERS. CAUTION! Adapter watt should follow default setting or refer to rating label information.
Resolution 1920*1080 supported Touch True-Flat PCAP touch Webcam Webcam Built-in FHD webcam module Packing List WMP2157 Power cord Medical adapter 1 x 90W/ 19V 2.2 Product overview Refer to the following illustration to identify the components on this side of the PPC. Features and configurations vary by model.
Page 13
Webcam 21.5" FHD LCD display (True-Flat PCAP touch) SSD 2.5", 7mm Potential equalization pin (POAG) DVI-D port COM 3 port (RS232/RS422/RS485) COM 2 port (RS232/RS422/RS485) Headphone / Line-out jack Microphone jack LAN (RJ45) ports...
Page 14
USB 3.0 ports HDMI port COM 1 port (RS232 only) Power jack (DC-IN) Power button Power switch: alternative (Depending on the model) Magnet...
3. Getting started Before using the rear I/O connectors, you need to remove the connector cover first. CAUTION! For safety reasons, please ensure that the power cord is disconnected before opening the case. Follow the steps (1 → 2 → 3) to remove the connector cover. ...
3.1 How to replace the 2.5" SSD 1. If you want to replace the 2.5" SSD, unscrew the thumbscrew and two screws of the bracket, then remove it. Old SSD 2. Unfasten the two screws (M3*4) and New SSD remove old SSD. As shown, install a new SSD in the bracket and secure with the two screws (M3*4).
3.2 Powering on the system Follow the steps (1-3) below to connect the AC adapter to the power jack (DC- IN). Press the power switch (4) to turn on the system. DC-IN Method 1: Depending on the model, press the power switch (a or b) to turn on the system.
3.3 Potential equalization When potential equalization between the PPC and other devices is required then connect the potential equalization pin (POAG) to the potential equalization terminal of the equipment. Poten�al equaliza�on pin (POAG) Poten�al equaliza�on cable (With 2 POAG-plugs) Other devices 4.
3.4 Cleaning the screen Follow these rules for cleaning the outside and handling your screen on the PPC: 1. Turn off the system and disconnect all cables. 2. Use a damp or cleaning cloth, soft, lint-free cloth with gentle water only and gently wipe the screen surface.
3.6 How to use touch panel (Optional) Touch panel brings digital life for an easy touch experience. Experience the ease of managing your digital life with a few touches. Your touch functions like a mouse device and all you need to interact with the touch panel. 1.
4. BIOS setup 4.1 About BIOS setup The default BIOS (Basic Input/ Output System) is already properly configured and optimized, there is normally no need to run this utility. 4.1.1 When to use BIOS setup? You may need to run the BIOS Setup when: 5.
Page 22
When OS support is Windows 10: 1. Click the Start menu and select Settings. 2. Select Update and Security. 3. Click Recovery 4. Under Advanced startup, click Restart now. 5. The system will restart and show the Windows 10 boot menu. 6.