1. Manuals
  2. Brands
  3. Wizard Manuals
  4. Industrial Equipment
  5. CMC Z1
  6. Getting started manual

Wizard CMC Z1 Getting Started Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Wizard™ CMC Model Z1
Getting Started Manual
FrameShop
FrameShop™
20-36070-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CMC Z1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Wizard CMC Z1

Summary of Contents for Wizard CMC Z1

  • Page 1 Wizard™ CMC Model Z1 Getting Started Manual FrameShop FrameShop™ 20-36070-1...
  • Page 2 This product and its documentation are protected by copyright and are distributed under license restricting its use, copying, distribution and decompilation. No part of this software product may be copied, reproduced or disassembled without written permission from Wizard and decompilation. No part of this software product may be copied, reproduced or disassembled without written permission from Wizard International, Inc.

  • Page 3: Table Of Contents

    Attach the M12 Cable to the Control Panel ............12 Hook up the Computer ....................13 Hook up Computer and Peripherals ..............13 Connect the ECU .....................14 Control Panel ........................15 Red Abort Button ....................15 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...
  • Page 4 Blades and Cartridges ....................29 Aborting a Cut .......................29 Head LED Behavior ......................29 LED Clamp Behavior ....................30 Troubleshooting ......................31 Frequently Asked Questions ..................32 Hardware Maintenance ....................33 Maintenance Schedule ...................33 Disclaimers ........................34 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 5: Check Contents

    Wizard CMC Model Z1 Hardware and Software Getting Started Manual Check Contents Review equipment upon arrival for shipping damage. Contact Wizard if any damage is noticed. Verify that the contents shown in the packing slip are received. Please save the packaging. Equipment Required The CMC Stand must be assembled first before unpacking the Wizard™...

  • Page 6: Cmc Parts

    CMC Parts Head Labeled Cartridges 45° 45° 45°+ 45°+ 52° 52° 90° 90° Deboss Deboss Deboss Thin Medium Wide ECU and Air Regulator Air Regulator Air Regulator 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 7: Cmc Parts Labeled

    N: Horizontal tension adjustment (lower rail) G: Vertical clamp O: Horizontal tension adjustment (upper rail) H: Gantry P: Control Panel Q: ECU Brackets (attach to back of CMC) 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 8: Setting Up The Cmc

    1. Locate the four shipping blocks holding the gantry in place. There are two on either side of the gantry on top of the upper rail. either side of the gantry on top of the upper rail. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 9: Check Squareness

    If they do not, call Wizard Technical belt and the toothed pulley. If they do not, call Wizard Technical Support.

  • Page 10: Head Installation

    Note that the notched side is placed tensioner after the head is slid onto the gantry. Note that the notched side is placed toward the gantry. toward the gantry. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 11: Hooking Up The Gantry And Air Lines

    If the board cable is obstructed, caught on anything. If the board cable is obstructed, this will affect the cuts. this will affect the cuts. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 12: Attaching The Air Lines

    5. Turn on the air. 5. Turn on the air. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 13: Hook Up The Computer

    6. Plug in the computer power cord into the matching port on the computer, then plug the power cord from the computer into a surge protector. plug the power cord from the computer into a surge protector. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 14: Connect The Ecu

    ECU when we hooked up the gantry previously. “Connecting the Board Cable” page 11 for more information. 10. The ECU is now connected. 10. The ECU is now connected. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 15: Control Panel

    ECU to turn on the ECU. *The ECU must be on for the CMC to cut. Press | on the rocker switch to turn it on.* 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 16: Boot Up The Computer

    Edit Opening Size First is unchecked in the is unchecked in the Admin > Defaults Admin > Defaults. . Optionally, enter the outside dimensions first. Optionally, enter the outside dimensions first. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...
  • Page 17 3. Click on new template thumbnail to select it. 3. Click on new template thumbnail to select it. 4. The new template is displayed. 4. The new template is displayed. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 18: Go To Cut Preview To Cut The First Mat

    1.Select the desired Layer Layer on the Cut Preview Screen. on the Cut Preview Screen. 2. Click on the 2. Click on the Blade Blade Depth Depth button. button. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...
  • Page 19 WARNING: Do not run the CMC without the blade cartridge in place or damage to the blade cartridge release lever could occur. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...
  • Page 20 See “Insert Blade Cartridge and Adjust See “Insert Blade Cartridge and Adjust Blade Depth” page 22 for more information Blade Depth” page 22 for more information. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 21: Align The Head When Motors Are Disengaged

    9. Make sure that the Pen, Vinyl and Crease tools are not in the foot block. It will then align the head as described below. 10. After aligning the head, it will immediately proceed to the Cartridge Change screen. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 22: Insert Blade Cartridge And Adjust Blade Depth

    2. Remove the matboard from the CMC. The first mat has been cut. If The Cut Doesn’t Look Right See “Troubleshooting” on page 29 “Troubleshooting” on page 29 for more information. for more information. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 23: Design A Different Mat

    2. If you have Remnant Trimming on, located under Set Advanced Set Advanced Options Options, it will also cut off the scrap edge. , it will also cut off the scrap edge. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 24: Adjusting Clamps For Zero Waste

    When the clamps are engaged, they will be retracted flush with the clamps are engaged, they will be retracted flush with the board. board. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 25: Mat Clamp Pressure

    Adjusting the Clamp Pressure Clamp Pressure Adjustment To adjust the clamp pressure, see “Clamp Pressure Adjustment” page 15” To adjust the clamp pressure, see “Clamp Pressure Adjustment” page 15”. . 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 26: Variable Pressure Optimization (Vpo) Feature

    For High Setting: Turn the air regulator pressure knob clockwise until the marker on the gauge is at the high setting. Make sure the gauge does not go above 60 psi. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 27: Cutting An Extra Dense Layer With The 90° Cartridge

    90° cartridge and changing the blades. information on the 90° cartridge and changing the blades. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 28: Changing The Blade

    8. If the pen is not going to be used for a while, please remove it from the pen holder and replace the pen cap to keep it from drying out. to keep it from drying out. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 29: Blades And Cartridges

    Green Solid CMC is cutting Green Blinking Waiting for a cartridge/blade change Green Solid Depth is being changed. Purple Blinking Error State. Solid Emergency Stop Pressed Blinking 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 30: Led Clamp Behavior

    User clicks Cut and a clamp is not If the user hits cut and a clamp engaged. is not engaged and it should be, the clamp LED will flash green. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 31: Troubleshooting

    “Blade Depth Settings” page 18 and Changing the Blade Depth in Check the Blade Depth. See and Changing the Blade Depth in FrameShop at FrameShop at https://wizardcutters.atlassian.net/wiki/spaces/FrameShop4x/pages/95129076/Changing https://wizardcutters.atlassian.net/wiki/spaces/FrameShop4x/pages/95129076/Changing +the+Blade+Depth+FrameShop+Cut+Preview+Screen +the+Blade+Depth+FrameShop+Cut+Preview+Screen. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 32: Frequently Asked Questions

    Click check for corners on the license screen. FrameShop will use the internet connection to download corners. If not connected to the internet, FrameShop can connect to Wizard via a modem. corners. If not connected to the internet, FrameShop can connect to Wizard via a modem.

  • Page 33: Hardware Maintenance

    The dial on the air regular should read 60psi when the air source is on and at full pressure. If it does not read 60psi on the gauge, call technical support. pressure. If it does not read 60psi on the gauge, call technical support. 20-36070-1 GettingStartedManualZ1FrameShop Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide 04/07/21...

  • Page 34: Disclaimers

    Wizard™, MatDesigner™, FrameShop™,Virtual Gallery®, SwitchBlade Technology™, the Wizard logo, MatDesigner logo, FrameShop logo and Integrated Framer logo are trademarks or registered trademarks of Wizard International, Inc. in the FrameShop logo and Integrated Framer logo are trademarks or registered trademarks of Wizard International, Inc. in the United States and/or other countries.

Table of Contents