Summary of Contents for CS Unitec KING-BOA
- Page 1 KING-BOA p/n 38810U (110 – 120V) Original instructions ....... 4 Particulate filter (40092)........12 Powered by www.csunitec.com Made in Germany Made in Germany...
- Page 2 KING-BOA www.csunitec.com...
- Page 3 KING-BOA www.csunitec.com...
-
Page 4: Table Of Contents
Original instructions KING-BOA Englisch 2. Specified conditions of use This belt sander is suitable for satin finishing, matt finish- ing, structuring, polishing and smoothing of round tubes Table of contents without the use of water. 1. EC-Declaration of conformity ....12 It is for dry processing only. -
Page 5: General Safety Information
Original instructions KING-BOA • Check prior to each use that the sanding belt is 4. General safety information correctly attached and is completely on the rollers. Carry out a trial run: Allow the machine to run at idling speed for 30 seconds in a safe location. Stop WARNING –... - Page 6 Original instructions KING-BOA • Do not use accessories that require liquid Special safety instructions for mains powered coolants. Using water or other liquid coolants may machines: result in electrocution or shock. • Pull the plug out of the socket before making...
-
Page 7: Product Features
6. Product features Some of the dust created using this power tool may contain chemicals known to cause cancer, KING-BOA, see page 2, figure A1 and allergic reaction, respiratory disease, birth defects or page 3, figure A2: other reproductive harm. Some of these substances... -
Page 8: Technical Data
Original instructions KING-BOA 7. Technical data Subject to change in accordance with technical progress. High-energy, high-frequency interferences can cause speed fluctuations. The fluctuations disappear, however, Measured values determined in conformity with as soon as the interference fades away. The technical EN 60745. -
Page 9: Accessories
Original instructions KING-BOA 8. Accessories 9. Initial operation Adjustable additional handle (A2-1): Only use original Eisenblätter accessories. See page 2, figures B1, B2 and B3: Use only accessories that fulfil the requirements and The additional handle can be remounted for working in specifications listed in these operating instructions. -
Page 10: Attaching The Tools, Working Notes
Original instructions KING-BOA 10. Attaching the tools, working notes 11. Switching on and off Prior to any conversion work: Pull the mains plug Always guide the machine with both hands. out of the socket or remove the battery pack from the machine. -
Page 11: Troubleshooting
Original instructions KING-BOA 12. Troubleshooting 14. Repairs The electronic signal indicator (A2-10) lights Repairs to power tools must only be carried out by up and the load speed decreases. qualified electricians! There is too much load on the machine! Run the... - Page 12 Feinstaubschutz-Kappe 40092 Filtergitter 40093 Originalbetriebsanleitung Particulate matter pr otection cap 40092 Filter fabric 40093 Original instructions Powered by www.csunitec.com Made Made in in Germany Germany...
- Page 13 ORIGINALBETRIEBSANLEITUNG EISENBLÄTTER 40092 / 40093 ORIGINAL INSTRUCTIONS EISENBLÄTTER 40092 / 40093 Lösen sie mit leichtem Druck Entfernen Sie den Filterhalter, indem Sie es mit einem spitzen die Feinstaubschutz-Kappe Gegenstand – wie z. B. ein Schraubendreher – vorsichtig aus den vier von der Maschine.
- Page 14 22 Harbor Ave, Norwalk, CT 06850 USA 1-800-700-5919 (USA & Canada) 203-853-9522 (outside USA & Canada) Fax: 203-853-9921 info@csunitec.com Internet: www.csunitec.com Made in Germany...
Need help?
Do you have a question about the KING-BOA and is the answer not in the manual?
Questions and answers