Motorola SYMBOL LS2208 Quick Start Manual page 2

1
Avoid Extreme Wrist Angles
AVOID EXTREME
WRIST ANGLES
© MOTOROLA, INC. 2008 All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of
any product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products might be used. An implied
license exists only for equipment, circuits, and subsystems contained in Motorola products. MOTOROLA, the
Stylized M Logo and Symbol and the Symbol logo are registered trademarks of Motorola, Inc. Other product
names mentioned in this manual may be trademarks or registered trademarks of their respective companies
and are hereby acknowledged.
Motorola, Inc. One Motorola Plaza, Holtsville, N.Y. 11742-1300 • http://www.motorola.com/enterprisemobility
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Patents
This product is covered by one or more patents. For patent information go to:
http://www.motorola.com/enterprisemobility/patents.
Service Information
If you have a problem using the equipment, contact your facility's Technical or Systems Support. If there is a
problem with the equipment, they will contact the Motorola Enterprise Mobility Support at:
http://www.motorola.com/enterprisemobility/contactsupport.
Waste Electrical and Electronic Equipment (WEEE)
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA
1-800-927-9626 http://www.motorola.com/enterprisemobility
72-71882-01
Rev C November 2008
SYMBOL LS2208
OPTIMUM SCANNING POSITIONS
2
3
1 LED
2 Scan Window
3 Scan Trigger
OPTIMUM UPRIGHT BODY POSTURE
Avoid Bending
AVOID BENDING
REGULATORY INFORMATION
http://www.motorola.com/ls2208
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered
in the U.S. Patent and Trademark Office. All other product or service names are the property
of their respective owners. © Motorola, Inc. 2008
Avoid Reaching
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk
of ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety
programs to prevent employee injury.
•
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
AVOID REACHING
Regulatory Information
Symbol Technologies, Inc., the Enterprise Mobility business of Motorola, Inc. ("Motorola").
All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and
will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol
Technologies, could void the user's authority to operate the equipment.
Laser Devices
Symbol products using lasers complies with 21CFR1040.10 and 1040.11,
EN60825-1:1994+ A1:2002 +A2:2001 and IEC60825-1:1993+A1:1997+A2:2001.
The laser classification is marked on one of the labels on the product.
Class 1 laser devices are not considered to be hazardous when used for their intended purpose.
The following statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser
is not known to be harmful.
Radio Frequency Interference Requirements
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Symbol Technologies, Inc., hereby declares that this device is in compliance with all the applicable Directives,
89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from
http://www.motorola.com/enterprisemobility/doc
Japan (VCCI) - Voluntary Control Council for Interference
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラス B 情
報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この装置がラ
ジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual.
Recommended Usage Guide
0 1 2 3 4 5
0 1 2 3 4 5
Reduce or eliminate repetitive motion
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed