Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dahua Technology PFM364L-D1
Summary of Contents for Dahua Technology PFM364L-D1
- Page 1 User’s Manual Integrated Solar Power System User's Manual User's V1.0.0...
-
Page 2: Foreword
This manual introduces the functions and operations of the integrated solar power system (hereinafter referred to as the "System"). Models PFM364L-D1, PFM363L-D1, PFM363L-SD1, and PFM372-L45-4S14P Safety Instructions The following categorized signal words with defined meaning might appear in the manual. - Page 3 User’s Manual errors in print. If there is any doubt or dispute, we reserve the right of final explanation. Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. All trademarks, registered trademarks and the company names in the manual are the ...
-
Page 4: Important Safeguards And Warnings
User’s Manual Important Safeguards and Warnings This chapter describes the contents covering proper handling of the integrated solar power system, hazard prevention, and prevention of property damage. Read these contents carefully before using the System, comply with them when using, and keep it well for future reference. -
Page 5: Table Of Contents
Features ............................1 2 Packing List ............................2 3 Structure ..............................3 Appearance ........................... 3 Dimensions ........................... 5 3.2.1 PFM364L-D1 ........................5 3.2.2 PFM363L-D1 and PFM363L-SD1 ..................6 3.2.3 PFM372-L45-4S14P ......................7 4 Installation .............................. 9 Preparation ............................ 9 4.1.1 Installation Site Requirements .................... 9 4.1.2 Tools ............................ -
Page 6: Overview
User’s Manual Overview Introduction This off-grid integrated solar power system consists of solar panel, lithium battery pack, maximum power point tracking (MPPT) charge controller, and mounting bracket. The System can be used in places without power supply and network connection. Specifically, it is applicable to the following scenarios: Supplying power for surveillance devices installed at places such as small construction ... -
Page 7: Packing List
After opening the packing box, check whether there is any obvious damage to the System, and make sure that all the items included in the packing list are provided. Packing list (PFM364L-D1, PFM363L-D1, and PFM363L-SD1) Table 2-1 Packing list description (1) -
Page 8: Structure
User’s Manual Structure Appearance Components (PFM364L-D1 and PFM363L-D1) Table 3-1 Component description (PFM364L-D1 and PFM363L-D1) Name Description Male circular connector Connector pin. Gear for adjusting horizontal and vertical angles. 5 Gear for adjusting angle degrees will be adjusted by rotating each slot. - Page 9 User’s Manual Components (PFM363L-SD1) Table 3-2 Component description (PFM363L-SD1) Name Description Male circular connector Connector pin. Gear for adjusting horizontal and vertical angles. 5° Gear for adjusting angle will be adjusted by rotating each slot. Attach the mounting sleeve to the pole, and then Mounting sleeve tighten the sleeve.
-
Page 10: Dimensions
User’s Manual Components (PFM372-L45-4S14P) Table 3-3 Component description (PFM372-L45-4S14P) Name Description Female circular connector Connector socket. Battery box Hold batteries. Dimensions 3.2.1 PFM364L-D1 Front view (mm [inch]) -
Page 11: Pfm363L-D1 And Pfm363L-Sd1
User’s Manual Side view (mm [inch]) Top view (mm [inch]) 3.2.2 PFM363L-D1 and PFM363L-SD1 Front view (mm [inch]) -
Page 12: Pfm372-L45-4S14P
User’s Manual Side view (mm [inch]) Top view (mm [inch]) 3.2.3 PFM372-L45-4S14P Front view (mm [inch]) - Page 13 User’s Manual Side view (mm [inch]) Top view (mm [inch])
-
Page 14: Installation
User’s Manual Installation Preparation 4.1.1 Installation Site Requirements The installation site shall meet the requirements of electrical and relevant fire prevention codes. Choose an installation site with sufficient sunshine all the year round, and make sure no shelter around the site to ensure natural lighting. If there is shelter at the installation site, make sure the lowest installation position of the ... -
Page 15: Cables
PFM364L-D1 and PFM372-L45-4S14P for example. Open the package, and place the System on a flat surface. Attach the lithium battery (PFM372-L45-4S14P) to the System (PFM364L-D1). Align two circular connectors, and then connect them firmly. Insert the connectors into each other... - Page 16 User’s Manual Fasten the connectors Place the battery onto the System, align the screws holes, and then fasten the M6 screws with a S5.0L wrench. Install the battery Adjust the horizontal angle. Use a S10.0L wrench to loosen M12 screw.
- Page 17 User’s Manual Installation diagram (1) Rotate the mounting sleeve 90°. Installation diagram (2) You can know the rotated angle according to the quantity of slots that have been rotated. 5° will be adjusted by rotating each slot. The System is designed with gear for adjusting horizontal or vertical angle. ...
- Page 18 User’s Manual Installation diagram (3) Use a S10.0L wrench to tighten the screw. Adjust the vertical angle. Use a S10.0L wrench to loosen M12 screw. Installation diagram (4) Adjust angle of mounting sleeve until β equals to local latitude.
- Page 19 User’s Manual Installation diagram (5) Use a S10.0L wrench to to tighten the screw. Install camera mounting plate. Make the mounting plate parallel with the mounting sleeve, and then use a S6.0L wrench to tighten the plate. Installation diagram (6) Use a screwdriver to remove the cover of cable tray.
- Page 20 User’s Manual Installation diagram (7) Connect cables, and then close the cover of cable tray. Wire through the cable tray, and pull the cable out of the camera mounting plate. Installation diagram (8) Connect RS-485 serial line. Connect RS-485_A to port A of camera, and RS-485_B to port B. Connect 12.8V DC power output line of the System to power input line of camera.
- Page 21 User’s Manual Align the female circular connector with the male one, and then connect the connectors. Installation diagram (10) Fix the connecter with tape, and then insert the connector into the holder for connector. Installation diagram (11) Raise the System to mounting height, and then attach the mounting sleeve to the pole, and finally use a S6.0L wrench to tighten the sleeve.
- Page 22 User’s Manual Installation diagram (12)
-
Page 23: Daily Maintenance
User’s Manual Daily Maintenance Notes Tools: Ladder, screwdriver, multimeter, bucket, mop, and insulated gloves. Attention: Do not maintain the System when it is raining. Wear insulated gloves during maintenance. Maintenance interval: Twice a year. Instructions It is recommended to check the following items to keep the long-term high performance of the System: Check whether the insulation layers of all exposed cables have been damaged because ... -
Page 24: Lightning And Surge Protection
User’s Manual Lightning and Surge Protection The System adopts TVS lightning protection technology. It can effectively prevent damages from various pulse signals below 6000V, such as sudden and indirect lighting strike. But, when installing the System in the outdoor environment, you still need to take necessary precaution measures while maintaining your local electrical safety code. -
Page 25: Cybersecurity Recommendations
User’s Manual Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. - Page 26 User’s Manual The account lock feature is enabled by default, and we recommend you to keep it on to guarantee the account security. If an attacker attempts to log in with the wrong password several times, the corresponding account and the source IP address will be locked. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024~65535, reducing the risk of outsiders being able to guess which ports you...
- Page 27 User’s Manual The network should be partitioned and isolated according to the actual network needs. If there are no communication requirements between two sub networks, it is suggested to use VLAN, network GAP and other technologies to partition the network, so as to achieve the network isolation effect.
Need help?
Do you have a question about the PFM364L-D1 and is the answer not in the manual?
Questions and answers