Table of Contents
Advertisement
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
Risk of contact with uncovered parts of the rotating saw
blade
■
Kick-back of workpieces or parts of workpieces due to
improper adjustment or handling
■
Catapulting of faulty carbide tips from the saw blade
■
Damage to the respiratory system
NOTE: Wear respiratory protection masks containing
filters appropriate to the materials being worked. Ensure
adequate workplace ventilation. Do not eat, drink or
smoke in the work area.
■
Damage to hearing if effective hearing protection is not
worn.
WARNING! Dust from certain paints, coatings and
materials may cause irritation or allergic reactions to the
respiratory system. Dust from wood such as oak, beech,
MDF and others are carcinogenic. Material containing
asbestos should only ever be worked or processed by
qualified specialist operators.
WARNING! Injuries may be caused, or aggravated, by
prolonged use of a tool. When using any tool for prolonged
periods, ensure you take regular breaks.
MAINTENANCE
■
Do not modify the product in any way or use accessories
not approved by the manufacturer. Your safety and that
of others may be compromised.
■
Do not use the product if any switches, guards or
other functions does not work as intended. Return to
an authorised service centre for professional repair or
adjustment.
■
Do not make any adjustments whilst the saw blade is
in motion.
■
Always make sure the battery pack has been removed
from the product before making adjustments, lubricating
or when doing any maintenance on the product.
■
Before and after each use, check the product for
damage or broken parts. Keep the product in top
working condition by immediately replacing parts with
spares approved by the manufacturer.
■
The blade has sharp edges and may also remain hot
after cutting operations. Exercise extreme caution when
cleaning an exposed blade. Wear gloves to protect
yourself from personal injury.
■
Clean the saw and its accessories from dust regularly,
especially moving parts including the blade guard.
Use a hand brush or vacuum cleaner to remove dust
effectively. Do not use compressed air.
■
For greater safety and reliability, all repairs, including
changing brushes, should be performed by an authorised
service centre.
6
Original Instructions
WARNING! Do not attempt to disassemble the blade
guard assembly for cleaning or repair. Damaged guards
should not be used. Return to an authorised service centre
for repair or replacement.
Mitre and bevel angle calibration
If mitre and bevel angle calibration are needed, see pages
24 – 28 and follow the calibration instructions.
TRANSPORTATION AND STORAGE
■
When storing the product, remove the battery pack.
Store the product in a secure place that is not accessible
to children.
■
Clean the product using a brush and vacuum cleaner
before storage.
■
If you remove the saw blade or keep spares with the
unit, ensure they are in the original packaging to prevent
injury.
To secure the product prior to movement:
■
The product should be stored at the zero degree mitre
and bevel angle and locked in position. The handle
should be locked in the lower (safe) position with the
guards closed.
To move or transport in a vehicle:
■
Secure the product prior to movement as described in
the manual.
■
Remove the product from the bench top by releasing the
4 bolts, one at each corner. Secure the bolts for future
use. Carry the product using the top carrying handle or
side carrying handles with two hands.
■
When transporting in a vehicle, set the product on its
base and secure against movement.
SYMBOLS ON THE PRODUCT
Safety alert
Regulatory Compliance Mark (RCM).
Product meets applicable regulatory
requirements.
Please read the instructions carefully
before starting the machine.
Wear ear protection
Always wear eye protection.
Keep hands away from the cutting area
and sharp blade.
Do not expose to rain or use in damp
locations.
Wear safety gloves
Blade rotation direction (shown on saw
blade)
Advertisement
Table of Contents
