Blackweb BWD19AAA08 - Wireless Clock Radio With Bluetooth Speaker Manual

Features

Top

#	Item	Description
1	Mode button	Press to cycle between FM mode, BT mode and AUX mode (when Aux-in jack is connected )
2	Alarm button	In Clock mode, press to turn on or turn off alarm; In other modes, press to return to Clock mode; In any mode, press and hold 1 second to enter alarm clock settings.
3	Clock button	In other modes, press to return to Clock mode; In any modes, press and hold 1 second to enter clock settings.
4	Dimmer/Snooze/Sleep	When alarm rings, you can press to adjust the interval to repeat alarm. The alarm repeats ringing 10 minutes later. When alarm not rings, press it to adjust LED brightness, press and hold 2 seconds to set up sleep timer.
5	Volume Down/ Previous Track	In BT mode, press to switch to previous track; In FM Mode, press to tune in 0.1MHz increments or switch preset stations, double-click to start auto scan until find a lower available channel, and press and hold to decrease volume. In any modes, press and hold to decrease volume.
6	Play/Pause	In AUX mode and BT mode, press to play or pause audio; in FM mode, press to enter preset station play mode, press and hold 2 seconds to set preset station.
7	Volume Up/Next Track	In BT mode, press to switch to next track; In FM Mode, press to tune in 0.1MHz increments or switch preset stations, double-click to start auto scan until find an upper available channel. In any modes, press and hold to increase volume.

Rear

LED Digital Display

Package Contents

• 1x Clock Radio
• 1x 5V/3.2A Power Adapter
• 1x User Guide
• 1x Quick Start Guide

Connect to Power

• Risk of product damage! Use the include 5V power adapter ONLY. Connect the AC power cord to the wall socket.

Set Clock Time
Time In any modes, press and hold button for 1 second, you will see the LED hour section blinks, then press or button to adjust the hour, after hour is set, press button to switch to minute, the LED minute blinks, then press or button to adjust the minute, after minute is set, press to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically).

Set Alarm Time
In any modes, press and hold button for 1 second, you will see the LED hour section blinks, then press or button to adjust the hour, after hour is set, press button to switch to minute, then press or button to adjust the minute, after minute is set, press button to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically).

Set Alarm Sound
After set the alarm minute, press button two times to enter alarm tone selection, then press or button to choose the tone you want (4 tones plus 1 FM radio tone), after tone is set, press button to confirm setting (If no button is pressed for 15 seconds, the setting is saved automatically).

Turn On/O Alarm
Press button to turn o or turn on alarm, the LED alarm icon keeps o or on correspondingly.

Return Factory Default
Press button for 10 seconds until "beep", the previous Clock settings, Alarm settings and Bluetooth paring settings will be cleared.

Use Snooze Feature

1. You can press to repeat alarm. When alarm rings, press button to snooze for 10 minutes.
2. When alarm rings, press any button (except button). The alarm stops, but the alarm settings remain.

Set the Sleep Timer

In BT/AUX/FM modes, press and hold button to adjust sleep timer, there are "90/60/30/15 minutes" and "OFF" total 5 options, after you get to the desired option, let go off button to confirm selection.

Play FM Radio

1. The default mode upon power on is FM mode. In other modes, press button to switch to FM mode. ( FM supports 87.5MHz to 108MHz)
2. Press or button to tune frequency for 0.1MHz each time, double-click or button to start auto scan, it stops until a station is found, auto scan will be interrupted by press or button.
3. Tune to the radio station you want to program, then press and hold button for 2 seconds to enter preset mode. The next available preset number (P-01 through P-10) appears on the LED. If you want to use a different preset number, press or button repeatedly until the number you want appears on the LED,then press button again to save your station and exit preset mode with "beep" voice prompt. (If no button is pressed for 15 seconds, the setting is saved automatically).
4. Press button to enter play preset station mode, and the last played preset station number (P-01 through P-10) appears on the LED, then press or button repeatedly until the preset station you want appears on the LED. Press button again to exit play preset station mode.
5. Press and hold or button to adjust volume, the volume level number appears on LED.

Adjust LED Brightness

When alarm no sounds, short press button to adjust LED brightness, there are low, medium and high three levels for selection.

Play Audio from a Bluetooth Device

The first time you connect your Bluetooth device to this player, you need to pair your device to this player.

Note:

• The operational range between this player and a Bluetooth device is approximately 10 meters (without any object between the Bluetooth device and the unit).
• Compatibility with all Bluetooth devices is not guaranteed.
• Any obstacle between this unit and a Bluetooth device can reduce the operational range.
• If the signal strength is weak, your Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically.

1. Press button to switch to BT mode, you will hear a "Bluetooth Mode" prompt tone, and clock radio automatically enters Bluetooth pair with Bluetooth name "Blackweb Clock Radio", there will be a "Bluetooth Pairing" prompt tone if pairing success and you will hear "Bluetooth Disconnected" when disconnected.
2. Press and hold button for 1 second to disconnect the current connected device, clock radio re-enters paring status.
3. When Bluetooth is disconnected, press button and clock radio will reconnect with the device that has connected before.
4. Press and hold or button to adjust volume, the volume level number appears on LED.

Connect an External Audio Device

1. In any mode, plug an audio cable with a 3.5 mm connector (not included) into the AUX IN jack on the back of your clock radio and into the audio out jack on your audio device, clock radio enters AUX mode automatically and plays the audio from your audio device, LED AUX icon keeps on.
2. Press and hold or button to adjust volume, the volume level number appears on LED.

Wireless Charging a Mobile Device

1. Plug in the included 5V/3.2A power adapter and your clock radio is powered on.
2. Make sure your device supports Qi charging technology.
3. Put your device horizontally on the wireless stand, DO NOT put it vertically as this will make it beyond charging arrange.
4. Your device will show charging status if charge successfully.

Charge a Mobile Device via USB-A Port

1. Plug in the included 5V/3.2A power adapter and your clock radio is powered on.
2. Connect a USB cable (not provided) to the USB port on the back of your clock radio and to the USB port on your device.
3. Your device will show charging status if charge successfully.