Summary of Contents for YUPACK Ausense FXJ-AT5050
- Page 1 The automatic folding carton sealer FXJ-AT5050 Operating instruction NAME: The automatic folding carton sealer MODEL: FXJ-AT5050...
- Page 2 PREFACE Thank you for purchasing the automatic folding carton sealer. This manual will show you the basic struture, using method and points for attention to use this machine safely and correctly. Please read this manual carefully before operating the machine. FX carton sealer seires use OPP tape to seal different kinds of cartons.
-
Page 3: Table Of Contents
Directory 1.Specifications ......................1 2. Brief introduction of main struture (P.2) ..............1 3. Instructions to adjusting parts ..................2 3.1 Table height adjustment (P.3) ................2 3.2 Width adjustment ....................3 3.3 Lateral pressure wheel adjustment (P.7) ............4 3.4 Back folding plate adjustment (P.8) .............. -
Page 4: Specifications
1.Specifications The semi-auto folding carton sealer can be operated singlely, with simple operation and high performance, for which it may be ideal packaging machine for you. The main specifications are listed as follows: Sealing width：150mm~500mm Sealing height：150mm~500mm Sealing length：200mm~600mm Table height：610mm~810mm Machine size：L1700 mm *W950 mm *H1750 mm Sealing speed：20m/min Power：220v 50/60HZ... -
Page 5: Instructions To Adjusting Parts
Spare parts list: S/N. Parts Name S/N. Parts Name S/N. Parts Name 1 Cylinder holder 19 Truckle 37 Rear folded plate 2 Connecting plate 20 Electromotor Protecting plate 3 Cylinder 21 Right side plate of the frame 39 Front folded plate 4 Lifting nut 22 Column Swing arm... -
Page 6: Width Adjustment
3.2 Width adjustment Shake the crank to adjust the width. Clockwise turn the crank for narrower, anticlockwise turn the crank for wider. (P.4) Turing the handle b51 to adjust the height. Clockwise (look out upon )turn the crank for higher, anticlockwise turn the crank for lower. (P.5) -
Page 7: Lateral Pressure Wheel Adjustment
Loosen the nut b61, moving the back folder controling switch along the long slot of the inner frame right side plate (P.6) 3.3 Lateral pressure wheel adjustment (P.7) Loosen the handle b71, manully move the lateral pressure wheel horizontal crustal. -
Page 8: Back Folding Plate Adjustment
3.4 Back folding plate adjustment (P.8) 3.5 Swing-rod adjustemnet (P.9) Loosen the nut b91, manually adjust the swing-rod to proper position 3.6 Adhesive tape installation and adjustment (P.10) 1.At first, install the roll of OPP adhesive tape at the core axis (see P.10), pull out of the adhesive tape, circle around roller B, then circle around roller C, D, get through tape seating F and get out of the front side of roller G. - Page 9 A d h e s iv e ta p e r o lle r S id e w i th g lu ti n o s ity R o lle r B R o lle r C C o p p e r d o lle r D T a p e h o ld e r F R o lle r G P .1 0...
- Page 10 4.Adhesive tape tension adjustment Turn the knob, loosen the nut M8, and adjust the bolt M8*50 to change the elasticity of swing-rod long extension spring so as to control the tape’s tension..Turn the knob clockwise and the tension of adhesive tape will largen; turn the knob anticlockwise, and the tension of adhesive tape will lessen.
-
Page 11: Operating Instruction
A d h e s iv e ta p e r o lle r K n o b S w in g - r o d lo n g e x te n s io n s p r in g B o lt M 8 * 5 0 N u t M 8 p o s t-... -
Page 12: Maintenance
10. Press the OFF switch to stop the machine. 5. Maintenance 1. The power and gas must be cut off when maintenance or adjustment is carried out. 2. Check if the oil of the oil-water separator is enough or not.Refuel promptly. it must use the special oil for air pressure and never use other kinds of replacing oil. -
Page 13: Exploded Figure
2. The carton must be dry. (Wet carton can’t be sealed) 3. No dust and garbage are allowed on the surface of the carton 4. Deformed cartons are prohibited for use. 5. The adhesive tape with different width and thickness can’t be used 6. - Page 14 Parts list Parts Name Parts Name Electromagnetic valve 21 Dextrorotation nut Upper-adhesive tape 22 Post-silk pole adhibiting set Upper-adhesive tape adhibiting set fixed 23 Sprocket wheel block Side covered plate 24 Axis sheath Handle 25 Driver Lateral pressure wheel 26 Motor connecting axis fixed block Lateral pressure wheel 27 Axis sheath...
-
Page 15: Exploded Figure Of Adhesive Tape Adhibiting Set
7.2 Exploded figure of adhesive tape adhibiting set Parts list: Parts Name Parts Name Screw M4*12 Swing-rod fixed axis ScrewM5*16 Swing-rod long extension spring ScrewM5*20 Fixed block ScrewM6*12 Fixup axis ScrewM6*16 Orientation spring ScrewM6*20 Rubber wheel axis ScrewM8*16 Rubber wheel ScrewM8*16 Orientation rubber wheel ScrewM8*50... - Page 16 NutM5 Unidirectional wheel NutM8 Unidirectional wheel bush NutM5 Unidirectional wheel gasket NutM6 Unidirectional wheel spring NutM8 Cutter bracket axis NutM8 Cutter bracket axis bush Gasket 3 Cutter holder Gasket4 Adjusted plate Gasket6 Cutter Gasket5 Cutter protecting cap Gasket6 Protecting cap torsion spring Gasket6 Protecting cap axis Gasket4...
-
Page 17: Malfunctions And Solutions
8. Malfunctions and solutions Malfunction and Solution of Folding Sealer Number Malfunction Possible reason Solution The reamer patch is not sharp Adhesive tape can not enough. Change the reamer patch be cut off The reamer tine is jammed by Launder the reamer patch the bond. -
Page 18: Electric Control
The speed of different straps Adjust each transporting There is jut before line’s pull to be consistent is different, and the carton is sealing and drape after not at the proper place when so that the carton can be sealing. pushing into the machine. - Page 19 Electric control parts: the power supply is 220VAC, 50HZ. 1 Phase. The electric circuit is composed of position switch, power switch, indicator and motor. 2. Operation procedures Opening orders: ①Adjusting the height and width of the sealer manually. ②Connect the air soure. ③Press the power switch “on”(ATTENTION: the machine has been switched on now.
-
Page 20: Inspection And Maintanance Of Pneumatic Control
9.3 Inspection and Maintanance of pneumatic control Genral method of inspeciton and maintanance of pneumatic control is very simple. It ‘s neccssary that you know the performance of the machine and the functions of all the position control points for the sake of safety. 1.The pneumatic control components: the pneumatic control system consists of air source processor, magnetic valve, cylinder and air pipes. -
Page 21: Common Malfunctions And Solutions
professional electrician can maintain and repair the machine. Common faults： 1.Unaction of the folding part when cases touching the “A” point Reasons: the position switch of “A” point is broken, or the connection of eletric circuit is bad, or faults of the air circuit. Troubleshooting method: check control points relating to the A point and check whether the eletric circuit looses or not. - Page 22 ①Check whether the thermorelay near the power switch trips or not and whether the power is off. ②Check whether the motor is right or not. ③Check whether chains works properly or not. ④Check whether motor shafts work normally or not. ⑤Check whether screws loose or not.