Sharp KB-3401LK Installation Manual page 5

frame where the ground screw was originally installed. See
Figure 8.
5 Make sure all screws are tightened securely and replace the
rear access cover and secure with screw. See Figure 6.
-wIRe connectIon InstRuctIons
For existing installations ONLY, refer to Figure 9.
 Follow the power supply cord kit manufacturer's Installation
Instructions and install the strain relief clamp. See Figure 7.
 Connect the end connectors for line 1, line 2 and neutral and
tighten securely to the terminal block. See Figure 9.
DO NOT LOOSEN the factory installed nut
IMpoRtant
connections which secure the range wiring to the terminal
block. Electrical failure or loss of electrical connection may
occur if these 3 nuts are loosened or removed.
 A ground strap is installed on this range which connects the
center terminal of the neutral terminal block to the range
chassis. The ground strap is connected to the range by the
center, lowest screw. See Figure 9. The ground strap must not
be removed unless National, State or Local Codes do not permit
use of a ground strap.
If the ground strap is removed for any reason, a
note:
separate ground wire must be connected to the separate ground
screw attached to the range chassis and to an adequate ground
source.
 Make sure all connections are tightened securely and replace
the rear access cover and secure with screw. See Figure 6.
-wIRe connectIon
Connect
line 1 here.
Cut ground
strap. Discard
ground strap
and ground
plate.
Connect green
insulated copper
ground wire with
ground screw
here.
Figure 8
-wIRe connectIon
Connect line
1 here.
Note: Install strain
relief clamp. Center
must always be
attached to the
center terminal on
block.
Figure 9
 & -wIRe peRManent wIRe connectIons
3–wire permanent connection – follow steps 1, 2 and 5 below.
4–wire permanent connection – follow all steps below.
Before wiring the range, review the suggested power source location
drawings in Figure 2. If connecting to a 4-wire electrical system:
Note: Install strain
relief clamp. Center or
white wire must always
be attached to the
center terminal on
block.
Connect line 2 here.
Connect neutral (white
or center) here.
terminal
A user supplied strain
block
relief clamp must be
line 1
installed at this
location. It requires 1
3 /8" (3.5 cm) diameter
Figure 0
cord kit hole.
Connect line 2 here.
Connect neutral
here.
ground
A user supplied
screw
strain relief clamp
must be installed
at this location. It
requires 1 3 /8"
(3.5 cm) diameter
cord kit hole.
Figure 
5
InstallatIon Manual
 Follow the manufacturer's Installation Instructions for installing
the strain relief clamp.
 Strip insulation away from the ends of the permanent wiring
for line 1, line 2 and neutral; also strip ground wire on 4-wire
connections. Tighten all 3 or 4-wire leads to the terminal block.
Follow wire locations shown in Figure 10.
DO NOT LOOSEN the factory installed nut
IMpoRtant
connections which secure the range wiring to the terminal
block. Electrical failure or loss of electrical connection may
occur if these 3 nuts are loosened or removed.
For 3-wire permanent connection skip steps 3 and 4
note:
and continue with step 5.
 Disconnect the ground strap. Remove the factory installed
ground screw and plate to release the factory installed copper
ground strap from frame of the range. Cut and discard the
copper strap from the terminal block. KEEP the ground screw,
ground plate and go to step 4.
 Connect the green ground wire lead to the frame of the range
using the ground screw and plate as shown in Figure 11. Be sure
to install using the same hole in the frame where the ground
screw was originally installed.
5 Make sure all connections are tightened securely and replace
the rear access cover and secure with screw. See Figure 6.
Non-terminated field wire compression connections
note:
must be set at approximately 90 in./lb.
FoR  & -wIRe peRManent connectIons
terminal
block
line 1
neutral
neutral ground strap
ground plate
ground
-wIRe peRManent connectIon only
screw
ground
plate
ground
ground
plate
screw
proper ground
ground
for 4-wire
wire lead
permanent
ground
wire lead
line 2
ground strap
line 2
ground plate
ground
screw
proper ground
for 4-wire
permanent