Configuring Parental Settings - Telefunken TNT UHDR10 AC4B User Manual

Hide thumbs

Table Of Contents

Table of Contents

If "USB disk writing speed too slow to record" message

is displayed on the screen while starting a recording,

try restarting the recording. If you still get the same

error, it is possible that your USB disk does not meet

the speed requirements. Try connecting another

USB disk.

Instant Recording

IMPORTANT: To record a programme, you should first

connect a USB hard disk or USB stick to your box. Otherwise,

recording feature will not be available. It is recommended

to use external hard disk drives instead of USB sticks for

programme recording and timeshifting.

Press the Record button to start recording an event

instantly while watching it. A recording screen will

then be displayed for a short time showing the current

event that will be recorded. Press Stop button to end

recording. A confirmation message will be displayed.

Select Yes and press OK to proceed. Select No and

press OK to continue recording.

You can not switch to a different broadcast during

the recording mode. A warning message appears on

the screen if your USB device speed is not sufficient.

Timeshift Recording

Press the Pause button while watching a broadcast to

activate timeshifting mode. In timeshifting mode, the

programme is paused and simultaneously recorded

to the connected USB disk drive. Press the Play

button again to resume the paused programme from

where you stopped. This playback is performed in

x1 playback speed. You will see the timeshift gap

between the real and the timeshifted programme in

the info bar. Use the Rapid reverse/Rapid advance

buttons to move forward or backward on timeshift

playback. Press the Stop button to stop timeshift

recording and return to the live broadcast.

You can not switch to a different broadcast or view the

media browser and main menu during the timeshifting

mode. Timeshift recording will not be available for

radio channels. A warning message appears on the

screen if your USB device speed is not sufficient.

Watching Recorded Programmes

Select Recordings from the Device menu. Select a

recording from the list, if any available. Press the OK

button to view the Options menu. Select an option

then press OK button.

Press the Stop button to stop a playback and return

to the Recordings screen.

Note: Viewing main menu and menu items will not be

available during the playback.

Recording Settings

You can configure your recording preferences using

the Settings tab in the Device>Recordings menu.

Highlight the Settings tab and press OK.

Start early: You can set recording timer's starting time

to start earlier by using this setting.

End late: You can set recording timer's end time to

end later by using this setting.

Max Timeshift: Using this option you can set the

maximum duration for timeshift recording. Available

options are approximate and the actual recording time

may change in practice depending on the broadcast.

The reserved and free storage space values will

change according to this setting. Make sure that you

have enough free space otherwise instant recording

may not be possible.

Auto discard:

Discard

Using this option you can have old recordings

deleted automatically, in case there is not enough

disk space for new recordings. You can set the

longest, shortest or oldest recording to be deleted

first. Use the Left/Right directional buttons to set.

Unplayed

If this option is set to Included, unplayed recordings

can be deleted automatically depending on the

configuration of the Discard option. This option will

only be available if the Discard option is set to a

value other than None. Set your preference using

the Left/Right directional buttons.

Hard disk information: You can view detailed

information about the USB storage device connected

to your box. Highlight and press OK to see and press

Back/Return to close.

Format Disk: If you want to delete all files on the

connected USB storage device, you can use Format

Disk option.

Press OK while the Format Disk option is highlighted.

A menu will appear on the screen, requiring you

to enter the PIN (*). After you enter the PIN, a

confirmation message will be displayed. Select Yes

and press OK to start formatting the USB storage

device. Select No and press OK to cancel.

(*) Default PIN could have been set to 0000 or 1234. If you

have defined the PIN (is requested depending on the country

selection) during the First Time Installation use the PIN that

you have defined.

Important ! Formatting your USB drive will erase ALL

the data on it and its file system will be converted to

FAT32. In most cases operation errors will be fixed

after a format but you will lose ALL your data.