Advertisement

For Serial Number 7I1437 and Higher
Models:
52060 — 950 RPM
52061 — Basic Versatility Kit
52062 — Deluxe Versatility Kit
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes and regulations. Please refer
!
WARNING
to Dynabrade's Warning/Safety Operating Instructions for more complete safety information. See inside for Important Operating, Maintenance and Safety Instructions.
New/Updated Parts - Effective Serial Number 7I1437 and Higher.
02696 Bearing Replaces 02650 Bearing. • 02676 Rear Bearing Plate Replaces 01487 Rear Bearing Plate. • 02679 Shield added.
Index Key
No. Part # Description
No. Part # Description
1
13061 Arbor Assy.
23 02679 Shield
13059 Collar
24 01448 Throttle Lever
1
A
2
53153 Planetary Housing
25 95558 Retaining Ring
3
01041 Grease Fitting
26 12132 Pin
4
50784 Lock Screw
27 02133 Housing - 52060
5
50782 Adapter
28 01449 Valve Stem
6
54520 Bearing
29 95730 O-Ring
7
54475 Gear Shaft
30 01024 O-Ring
8
50780 Planetary Carrier
31 01469 Speed Regulator
9
06213 950 RPM Gear
32 01464 Seal
10 54468 Ring Gear
33 01472 Tip Valve
11 53150 950 RPM Pinion
34 01468 Spring
12 50778 Spacer
35 01564 Air Control Ring
13 53152 Gear Case
36 94520 Muffler Assy.
14 01547 Rubber Collar
37 95711 Retaining Ring
15 01007 Bearing
38 95438 O-Ring
16 53161 Front Bearing Plate
39 94521 Muffler Base
17 50777 Rotor
40 94524 Sintered Muffler
18 01480 Motor Blades (4)
41 94525 Felt Muffler
19 01476 Cylinder
42 94522 Muffler Cap
20 50767 Pin
43 95375 O-Ring
21 02676 Rear Bearing Plate
44 94526 Spacer
22 02696 Bearing
45 94523 Inlet Adapter
Key
Oil
Grease
N/UP
O
G
Loctite/Hernon: L
= Loctite #271
L
2
L
= Loctite #609, L
= Hernon #940
3
4
Torque: N•m x 8.85 = In. - lbs.
T
T
= 17 N•m, T
= 23 N•m, T
2
3
12
11
T
2
23
20
19
N/UP
22
21
N/UP
L
N/UP
2
25
Right
Hand
28
Threads
29
27
32
30
31
New/Updated
Part or Assy.
= 28 N•m
4
6
10
8
9
7
L
2
17
16
15
18
11
O
L
T
2
2
24
26
38
33
35
39
37
34
Parts Page Reorder No. PD98•10
Effective January, 1998
Supersedes PD97•04
Dyninger
Air Motor and Machine Parts
6
5
2
T
L
T
2
2
4
G
3
4
14
3
8
G
4
13
6
10
40
42
41
43
36
1
1
T
A
2
6
9
7
44
45
T
L
O
3
4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 52061 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dynabrade 52061

  • Page 1 Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes and regulations. Please refer WARNING to Dynabrade's Warning/Safety Operating Instructions for more complete safety information. See inside for Important Operating, Maintenance and Safety Instructions. New/Updated Parts - Effective Serial Number 7I1437 and Higher.
  • Page 2 2. Some silencers on air tools may clog with use. Clean and replace as required. 3. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).
  • Page 3 Important: Manufacturer’s warranty is void if tool is disassembled before warranty expires. Notice: Dynabrade strongly recommends the use of their 52296 Repair Collar (sold separately) during assembly/disassembly activities. Failure to use this collar will highly increase the risk of damage to the valve body of this tool. Please refer to parts breakdown for part identification.
  • Page 4 Important: Motor should now be tested for proper operation at 90 PSI. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed.

This manual is also suitable for:

5206052062

Table of Contents