Related Manuals for Sony Trinitron WEGA KV-HM213
Summary of Contents for Sony Trinitron WEGA KV-HM213
- Page 1 3-106-999-11 (1) Trinitron Color TV Operating Instructions • Before operating the unit, please read this manual thoroughly and retain it for future reference. KV-HM213 © 2007 Sony Corporation...
-
Page 2: Specifications
Specifications KV-HM213M80 Note Power requirements 110-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 Channel coverage VHF : E2 to E12 /UHF : E21 to E69 / CATV : S01 to S03, S1 to S41 UHF : B21 to B68 /CATV : S01 to S03, S1 to S41 VHF : C1 to C12, R1 to R12 /... - Page 3 WARNING • Dangerously high voltages are present inside the TV. • TV operating voltage: 110 – 240 V AC. • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
-
Page 4: Getting Started
Getting Started Step 1 Insert the batteries (supplied) into the remote. • Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. •... -
Page 5: Setting Up Your Tv ("Initial Setup")
Setting up your TV (“Initial Setup”) When you turn on your TV for the first time, the “Initial Setup” menu will appear. You can adjust settings below using the buttons on the remote control or TV top control panel. Press V, v, B or b to select or adjust items, then press Select the desired menu language. -
Page 6: Connecting Optional Components
Connecting optional components You can connect a wide range of optional components to your TV. Connecting cables are not supplied. Connecting to the TV (front) Audio/Video Camcorder cable (MONO) (MONO) Headphones Connecting to the TV (rear) Audio (MONO) (MONO) System Audio/ Video cable... -
Page 7: Troubleshooting
• Count the number of times the 1 (standby) indicator flashes. Press ! (main power) to turn off your TV. Contact your nearest Sony service center. The TV screen sometimes goes blank for slightly longer than usual during channel change. -
Page 8: Tv Buttons And Remote Control
TV buttons and remote control WEGA GATE PROG SOUND MODE Turn off or turn on the TV. Remote control sensor. Wake Up indicator. Standby indicator. PROG +/– Select program number. 2 +/– Adjust volume. Select TV or video input. WEGA GATE menu operations (see H) V,v,B,b Select or adjust items. - Page 9 TV buttons and remote control (continued) Select sound mode options with a 5-Band Graphic Equalizer display: “Dynamic”, “Standard”, “Custom”* (see J). Standard Custom Dynamic 100 300 1k 3k 8k 100 300 1k 3k 8k 100 300 1k 3k 8k * When the “Custom” mode is selected, you can receive the last adjusted sound settings from the “Sound Adjustment”...
-
Page 10: Wega Gate Navigator
WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs and “Settings” menu. WEGA GATE External Inputs “TV” watch the preset TV Settings channels (see D) Select Select Confirm Confirm External Inputs Video 1 “External Inputs”... -
Page 11: Picture Setting
“Picture” setting Press WEGA GATE and select “Settings”. Picture Picture Mode: Vivid Make sure the “Picture” icon ( ) is selected, Picture Adjustment then press Color Temperature: Cool Intelligent Picture: Signal Level Indicator: Select Confirm “Picture Mode” Choose either “Vivid” (bright, contrast and sharp), “Standard”... -
Page 12: Sound Setting
“Sound” setting Press WEGA GATE and select “Settings”. Sound Press V or v to select the “Sound” icon ( ), Sound Mode: Dynamic Sound Adjustment then press Balance Intelligent Volume: Surround: Select Confirm “Sound Mode” Choose either “Dynamic” (low and high tones), “Standard” (voice and high tones) or “Custom”*. -
Page 13: "Channel Setup" Setting
“Channel Setup” setting Press WEGA GATE and select “Settings”. Channel Setup Auto Program Press V or v to select the “Channel Setup” Manual Program Program Sorting/Edit icon ( ), then press Select Confirm “Auto Program” Preset channels automatically. “Manual Program” Manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually). - Page 14 “Channel Setup” setting (continued) Presetting channels manually After selecting “Manual Program”, select the program number to which you want to preset a channel. (1) Make sure “Program” is selected, then press (2) Press V or v until the program number you want to preset appears on the menu, then press Select the desired channel.
-
Page 15: Setup Setting
“Setup” setting Press WEGA GATE and select “Settings”. Setup Language: English Press V or v to select the “Setup” icon ( Video Label Color System: Auto then press Wake Up Timer Beep: Factory Settings Select Confirm “Language” Change the menu language. Press V or v to select either “English”...