Advertisement
5. OPERATION
5.1.
Air Supply
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the drill. Too high an air pressure and unclean
air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
5.1.1. Ensure drill air valve (or trigger) is in the "off" position before connecting to the air supply.
5.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
5.1.3. Drain the air tank daily. Water in the air line will damage the drill.
5.1.4. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.
5.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should
be 1/4" internal diameter and fittings must have compatible dimensions.
5.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
5.2.
Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the drill. To overcome this, connect a leader hose to the
drill (Sealey ref: AH2R or AH2R/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose.
See fig 1 & fig 2.
fig 1
5.3
In Use
WARNING! Ensure you read, understand and apply Section 1 safety instructions.
5.3.1. Slide the side handle over the drill body, set to desired position and rotate the grip clockwise to tighten.
5.3.2. Turn front of chuck head to open, insert drill bit and turn chuck head to lock drill bit.
5.3.3. Connect the drill to the air hose (fig.2).
5.3.4. The drill direction is changed by switching the forward-reverse lever above motor housing. Check that the drill is set to operate in the
required direction.
5.3.5. Depress the trigger to operate the drill accordingly.
5.3.6. To remove side handle, rotate the grip counter-clockwise and slide away from drill body.
DO NOT allow the drill to free run for an extended period of time as this will shorten its life.
6. MAINTENANCE
WARNING! Disconnect drill from air supply before changing accessories, servicing or performing maintenance. Replace or repair
damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
6.1.
Lubricate the air drill daily with a few drops of Sealey air tool oil dripped into the air inlet to prolong its life.
6.2.
Clean the drill after use.
6.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connectors. To remedy check the
air supply and follow instructions in Section 3.
b) Grit or gum deposits in the drill may also reduce performance. If your model has an air strainer (located in the area of the air inlet),
remove the strainer and clean it. Flush the drill out with gum solvent oil or an equal mixture of SAE No 10 oil and paraffin. Allow to
dry before use.
6.4.
For a full service contact your local Sealey service agent.
6.5.
When not in use, disconnect from air supply, clean the drill and store in a safe, dry, childproof location.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, dispose of the product according to local regulations.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig 2
www.sealey.co.uk
01284 757500
01284 703534
sales@sealey.co.uk
SA621.V2 Issue: 2(SP) - 24/11/15
Advertisement
