Viatek RENU-IT PRO Series -Disposable Battery Recharger Manual
- Directions for use (2 pages)
Advertisement
PARTS DIAGRAM
- DC SOCKET
- LED LIGHT (9V BATTERY)
- CHARGING (9V BATTERY)
- +POLE
- BATTERY SELECTION SWITCH
- -POLE
- BATTERY CHARGER BAY
- POWER LIGHT
- LED INDICATORS
- LCD DISPLAY
DEVICE USE TABLE
| Battery TYPE | Function | LED Indication | LCD display word | LCD capacity Indication |
| Ni-Cd | Discharge | Orange | DIS | Blinking downward |
| Charging | Red | CHA | Flashing upward | |
| Fully charged | Green | OK | Fully charged | |
| Ni-MH | Charging | Red | CHA | Flashing upward |
| Fully charged | Green | OK | Fully charged | |
| Alkaline | Charging | Red | CHA | Flashing upward |
| Fully charged | Green | OK | Fully charged | |
| Ni-Cd Ni-MH Alkaline | Battery voltage is very low short Battery can't recharge | Off | BAD |
USING THE DEVICE
NOTE: Only one battery chemistry can be charged at one time.
- Connect the AC adaptor to the power.
- Insert the AC adaptor plug into the DC socket
- Select the correct battery chemistry, Ni-Cd, Ni-MH or alkaline
- Insert the batteries into the charger, aligning each with the correct polarity.
- After inserting the batteries the LEDs will flash for approximately 2 seconds, then Renu-It Pro will automatically detect the status of the and indicate the status on the LED screen.
- The LCD will display "DIS" as it begins to discharge the battery, LED will light orange at the same time. When the discharging process is done, the battery will transfer to charge status automatically, and LCD display "CHA", LED will light red at the same time. When the battery is fully charged, the LCD will display "OK", battery bar on LCD display a full battery shape, and LED will light green.
NOTE: Ni-MH and Alkaline batteries do not have memory; The Renu-It Pro will automatically start to charge, (LCD display "CHA")
CHARGING TIMES
Charging time is different according to different brand and capacity of the battery, the formula below can be applied for reference.
Battery capacity x 1.4 = charging time
| Battery Type | Battery size | Battery capacity | Charge time |
| Ni-Cd | A A A | 400mAh | 0.7H |
| A A | 800mAh | 1.4H | |
| C | 2200mAh | 3.9H | |
| D | 4400mAh | 7.7H | |
| Ni-MH | A A A | 800mAh | 1.4H |
| A A | 2300mAh | 4H | |
| C | 3300mAh | 5-8H | |
| D | 5000mAh | 8H | |
| Alkaline | A A A | 1.5V | <1.4V 2.5H |
| A A | 1.5V | <1.4V 5H | |
| C | 1.5V | <1.4V 6H | |
| D | 1.5V | <1.4V 10H | |
| 9V block | 200mA h | 7H |
ADDITIONAL INFORMATION
The Renu-It Pro can only charge is only Ni-Cd (Nickel Cadmium) and the Ni-MH (Nickel Metal Hydride) and alkaline battery.
Don't use extension cable for connection of the device.
Pay attention to the correct polarity during inserting battery.
Store at room temperature. Extreme temperatures can damage the unit.
Clean the dust before using to ensure a good connection.
Don't use damaged or corroded battery into the charger.
300 mAh batteries can never be charged over 0.5 hours.
For customer service call 888.7.VIATEK or visit us online at viatekproducts.com
Viatek No Question Protection - Protect your product with Viatek Warranty Services. Product is replaced or reimbursed 100%. Protection for 1-year beyond our standard warranty, No shipping charges, no deductibles, Your product is protected from any mechanical or electrical failures caused by power surges or manufacturer's defects. Just $5.95, order online at viatekproducts.com today.
6881 Kingspointe Pkwy Ste 7
Orlando, FL 32819
407.248.0123
© 2008 VIATEK CONSUMER PRODUCTS GROUP, INC. All specifications and prices are subject to change without notice. All rights reserved.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Viatek RENU-IT PRO Series -Disposable Battery Recharger Manual
Advertisement
Need help?
Do you have a question about the RENU-IT PRO Series and is the answer not in the manual?
Questions and answers