Advertisement
2.
INTRODUCTION
Manufactured using high quality components for performance and reliability. Lightweight and compact made from heavy duty die cast
magnesium alloy. Fitted with a powerful magnet to ensure unit stays adhered at any angle. Includes safety fixing strap, 10mm twist drill
chuck and integrated coolant system to extend the life of cutters and increase the quality of the cut. Designed for use in fabrication,
construction and other applications when drilling ferrous metal.
3.
SPECIFICATION
Model No ........................................................MAG110V
Cable Length ........................................................... 2.2m
Magnet Adhesion ................................................14000N
Maximum Annular Cutter Capacity ........................ 35mm
Maximum Cutter Depth ......................................... 50mm
Motor Power .........................................................1500W
No Load Speed ................................................... 800rpm
Supply .........................................................110V ~ 50Hz
Consumables (not included)
Neat Cutting Oil .................................................. NCO/5L
Soluble Cutting Oil ............................................. SCO/5L
Pilot Rod ............................................................... RBSP
HSS Magnetic Drill Cutters
12mm ............................................................RBHSS12S
13mm ............................................................RBHSS13S
14mm ............................................................RBHSS14S
16mm ............................................................RBHSS16S
18mm ............................................................RBHSS18S
20mm ............................................................RBHSS20S
22mm ............................................................RBHSS22S
24mm ............................................................RBHSS24S
25mm ............................................................RBHSS25S
4.
ASSEMBLY
4.1.
FIT COOLANT BOTTLE Refer to fig.1
4.1.1. Slacken the 2 thumbscrews and slide bottle cage over the
thumbscrews. Tighten thumbscrews.
4.1.2. Connect coolant pipe to the valve on the drill head, fig.1.
4.1.3. Pipe can be released by pushing in the blue valve.)
4.1.4. Make sure the coolant tap is closed, fill the bottle with appropriate
lubricant.
4.2.
FIT CUTTING BIT
4.2.1. Wind drill head up to maximum height.
4.2.2. Wind the two grub screws, fig.2.6, in to secure the cutting bit.
5.
OPERATION
IMPORTANT: MAGNETIC BASE TROUBLESHOOTING
If the magnetic base is not working, first check the fuse and if required
replace with the spare fuse provided. See fig.2.
5.1.
Mark the position of the hole to be drilled on the workpiece.
5.2.
POSITION THE DRILL
5.2.1. Connect to the mains supply. Offer drill to workpiece and line up with
the previously marked hole.
WARNING! Make sure there is nothing between the magnet and the
‰
workpiece BEFORE turning the magnet on.
NOTE: When using drill vertically use the level, fig.2.7.
5.2.2. Ensure the drill head is wound back away from the workpiece before
turning the magnet on.
5.3.
ATTACH DRILL TO WORKPIECE
5.3.1. Turn the magnet on, fig.2.2. Wind the drill head down to the workpiece
and align the cutting head pin.
5.4.
FIT THE SAFETY STRAP
5.4.1. Place the safety strap though the handle of the drill and around the
steelwork. Adjust the length of the strap so that if the drill should fall the
drill should not be allowed to swing too far and be damaged.
5.5.
FILL COOLANT BOTTLE
5.5.1. Always use the correct cutting oil, refer to Section 3 and refill once it empties. Never use without coolant.
5.6.
CUTTING THE HOLE
5.6.1. Turn on the cooling tank tap, fig.1.
5.6.2. Back the cutting head away from the workpiece, turn the drill motor on, fig.2.1. Check the drill sounds and is operating normally.
5.6.3. Turn the handle, fig.2.3, anticlockwise to move the cutting bit towards the workpiece.
5.6.4. Start feeding slowly, with not too much force, to prevent overloading the drill.
CAUTION! Prepare for bursting through the workpiece.
5.6.5. If the drill suddenly stops, you must turn off the motor switch immediately.
© Jack Sealey Limited
Original Language Version
fig.1
fig.2
1 Motor switch
5 Slide adjusters (5 each side)
2 Magnet switch
6 Cutting bit grub screw (2 of)
3 Handle
7 Level
4 Fuse cover
8 Fuse cover (2 of)
MAG110V
Issue 3 (ALL)
17/07/23
Advertisement
