Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Carlisle Manuals
  4. Cutter
  5. Binkes 201-510
  6. Service manual

Carlisle Binkes 201-510 Service Manual

Roving cutter
Hide thumbs

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
EN
Extreme caution needed when using this product. Cutters have sharp blades which are
rotating at high speed. Never operate this product with the safety guard removed.
The 201-510 Roving Cutter is designed to cut glass
roving into short lengths (1/4" to 1"), and dispense
them into the resin fan. When properly adjusted, the
glass/resin mixture will need a minimum amount of
rolling.
The air supply hose must have a minimum 5/16" ID.
Lower air pressures or a smaller diameter hose could
result in poor operation.
77-2475-R7 (1/2022)
MODEL 201-510
ROVING CUTTER
WARNING
!
Max. Air Consumption:
Max. Air Inlet Pressure:
201-510 ROVING CUTTER
PACKAGE CONTENTS
207-12194
207-10903
1 / 12
27cfm (47 m
80 psi (5.52 bar)
ANGLED CHUTE
SPARE PARTS KIT
www.carlisleft.com
/h)
3

Advertisement

loading

Related Manuals for Carlisle Binkes 201-510

Summary of Contents for Carlisle Binkes 201-510

  • Page 1 SERVICE MANUAL MODEL 201-510 ROVING CUTTER WARNING Extreme caution needed when using this product. Cutters have sharp blades which are rotating at high speed. Never operate this product with the safety guard removed. Max. Air Consumption: The 201-510 Roving Cutter is designed to cut glass 27cfm (47 m Max.
  • Page 2 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: WARNING NOTE CAUTION Hazards or unsafe practices which Hazards or unsafe practices which could result in severe personal Important installation, operation or could result in minor personal injury, injury, death or substantial property maintenance information.

  • Page 3: Parts List

    MODEL 201-510 CUTTER ASSEMBLY PARTS LIST When ordering, please specify Part No. ITEM PART ITEM PART DESCRIPTION QTY. DESCRIPTION QTY. 1 207-11403 BACK PLATE ......... 1 14 207-11182 CHOPPER GUARD ASSEMBLY ..1 2 237-39 SOCKET HEAD SCREW ....1 15 237-175 HEX HEAD SCREW ....

  • Page 4: Operation

    Binks MODEL 201-510 ROVING CUTTER OPERATION: 8. For disassembling the air motor NOTE assembly (5), begin by removing To introduce roving to the cutter, the two pins (5d) holding the tire Lubrication is very important and double over one end of roving and shaft (5c) to the rotor.
  • Page 5 Binks MODEL 201-510 ROVING CUTTER WARNING USE CAUTION TO PREVENT ACCIDENTAL CUTS AS THESE BLADES ARE SHARP. Cutting Head Assembly: 3. Now you can add the manifold assembly (6) by sliding it into the back plate. Be sure to lubricate the three The cutter comes from the factory set to cut 1"...
  • Page 6 MODEL 207-12393 CHOPPER AIR MOTOR ASSEMBLY (ITEM NO. 5 IN PARTS LIST ON PAGE 4) REFER TO PART SHEET 77-2883 FOR DETAILS OF 5a PARTS LIST When ordering, please specify Part No. ITEM NO. PART NO. DESCRIPTION QTY. — AIR MOTOR ....1 237-22-K5 E-CLIP ......
  • Page 7 MODEL 207-11185 1" CUTTING HEAD ASSEMBLY (ITEM NO. 11 IN PARTS LIST ON PAGE 4) PARTS LIST When ordering, please specify Part No. ITEM NO. PART NO. DESCRIPTION QTY. 237-558 RETAINING RING ...... 2 237-574 BEARING ........1 207-11191-1 8 VANE CUTTING HEAD ..... 1 207-11186...
  • Page 8 MODEL 207-11415 CUTTER MOUNTING KIT (ITEM NO. 22 IN PARTS LIST ON PAGE 4) PARTS LIST When ordering, please specify Part No. ITEM NO. PART NO. DESCRIPTION QTY. 237-14 ROLL PIN ........1 207-11407 CUTTER ADJUSTMENT BRACKET ..1 20-263-1 WASHER ........
  • Page 9 BINKS MODEL 207-12393 CHOPPER AIR MOTOR ASSEMBLY PARTS LIST When ordering, please specify Part No. ITEM PART DESCRIPTION QTY. 1 ▲ SEAL .......... 1 2 ▲ BEARING ........2 DOWEL PIN ........ – DRIVE END PLATE....... – 5 ▲ SHIMS ........2 BODY .........
  • Page 10 ASSEMBLY INSTRUCTIONS: BINKS MODEL 207-12393 CHOPPER AIR MOTOR ASSEMBLY 1. Remove the end cap. 12. Place the proper end plate gasket on the body of dead end. If the original is damaged, replace 2. Remove dead end plate bolts. with a new one supplied in the Repair Kit (106- 3.

  • Page 11: Troubleshooting

    TROUBLESHOOTING TROUBLE PROBABLE CAUSE SOLUTION Glass wrap up. Wet glass or oil on anvil sleeve. Remove guard and clean out. Material in cutter guard. Blower control knob is shut. Open blower control knob. Tension adjustments. Correct tension adjustment. Dull or worn blades or anvil. Replace blades or anvil.

  • Page 12: Warranty Policy

    This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided may invalidate any warranty.