Loading the Silverware Basket Loading the Lower Rack Loading the Upper Rack Loading the Cutlery Rack Adding Cleaning Products 38 SMART FUNCTIONS SIGNATURE KITCHEN SUITE Application Smart Diagnosis Function 42 MAINTENANCE Cleaning and Care 46 TROUBLESHOOTING Before Calling for Service...
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE Safety Messages Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and follow all safety messages.
Page 4
• Do not grasp the power supply line or touch the appliance controls with wet hands. • Do not modify or extend the power cable. • If the product has been submerged, contact a SIGNATURE KITCHEN SUITE customer information center for instructions before resuming use.
Page 5
IMPORTANT SAFETY INSTRUCTIONS • Fix the drain hose securely in place. • Use only detergents or wetting agents recommended for use in a dishwasher and keep them out of the reach of children. • Do not let children eat detergent or dishwasher rinse agent. •...
IMPORTANT SAFETY INSTRUCTIONS Tip Over Hazard • Do not use the dishwasher until completely installed. • Do not push down on the open dishwasher door. • Failure to follow these instructions may result in serious injury or cuts. CAUTION STATEMENTS CAUTION •...
• Do not remove the safety cover at any time. • To ensure reliability, each SIGNATURE KITCHEN SUITE dishwasher goes through thorough quality control before it leaves the factory. • You may find water droplets or water spots from this process inside your new dishwasher.
Page 8
Tub Light manual may vary due to constant product improvements. NOTE Model SKSDW2401S • The silverware basket ships installed at the back of the bottom rack. For best performance, install Electrical 120 V, 60 Hz AC only, it along the right side.
INSTALLATION INSTALLATION Before Installing Parts not Provided Electrical Cable Flat-Blade Screwdriver • 16 AWG, with 2 conductors and 1 ground Phillips Screwdriver Water Supply Tube Hole Saw min. 2 1/2” bit • Minimum 3/8″ O.D. copper tubing or stainless steel braided water supply line Electric Drill Fittings for Tube Gloves...
10 INSTALLATION Installation Overview dishwasher. Water supply hose, drain hose and electric cable should be passed through this area. Please read the following installation instructions first after purchasing this dishwasher or 26 / - 26 / " (676 - 681 mm) transporting it to another location.
INSTALLATION Preparing Water and Choosing the Proper Location Electrical Connections Select a location as close to the sink as possible for easy connections to water supply line, drain hose and electrical connection. WARNING • Water Connection - Do not reuse an old hose. Use only a new hose when installing the dishwasher.
12 INSTALLATION Preparing Dishwasher Routing Water Supply Line and Electrical Wiring WARNING There are 2 channels in the bottom of the dishwasher for routing the water and electrical • Do not remove safety cover . Removal can connections. result in fire, electric shock or death. •...
INSTALLATION Remove the lower cover. Bend the tabs on the brackets to secure them If there is insulation padding behind the lower to the frame using a pair of needle nose cover, remove it. pliers. Set the parts aside until the installation is complete.
Page 14
14 INSTALLATION water supply. As you slide the dishwasher into CAUTION the opening, you will want to slowly pull on the drain hose from inside the cabinet to take • Do not push the top of the dishwasher. Doing so up some slack.
INSTALLATION Connecting Water Supply conduit pipe is longer than 3” (76 mm) and is centered on the back wall. Line and Power Turn off electrical power to the unit at the Connecting Water Supply Line circuit breaker. With the home water supply turned off, connect the water supply line to the inlet valve Use a Phillips screwdriver to remove the on the left front of the dishwasher.
16 INSTALLATION Wrap electrical tape around each connection. Insert the electrical cable through the hole in Fold the connected wires back into the the strain relief. Tighten 2 screws to secure junction box and screw on the junction box the cable. cover.
Page 17
INSTALLATION • Do not connect drain hoses from other appliances to the dishwasher’s drain hose. • If an extension drain hose is required, use a 5/8" or 7/8" inside diameter, 2-3 ft. length hose and a coupler for connecting the two hose ends. Height of the Drain Hose The height of the drain hose end must be at least Attach the drain hose to the disposal with the...
18 INSTALLATION Checking Leveling To check that the tub is level from front to back, remove the lower rack and pour 169 oz. (5 L) of water into the bottom of the tub. The water level should be near the center of both tub lower indentations at the front.
INSTALLATION • Turn the front leveling feet clockwise to raise the can safely be drilled into, secure the dishwasher to front of the tub and counterclockwise to lower it. the countertop with the provided brackets. If the countertop is granite, marble, or a material that cannot be drilled into, secure the dishwasher to the cabinet frame with the provided wood screws.
20 INSTALLATION If a water leak is detected, press and hold the Start button for 3 seconds to cancel the wash cycle and automatically drain the water from the dishwasher. Tighten all water connections and run another cycle. Repeat until no leaks are detected.
Page 21
INSTALLATION Error Code Possible Cause and Solution Water supply line is kinked under dishwasher. • Feed the drain and water supply hoses through the hole under the sink. Then gradually slide the dishwasher into the cabinet while pulling on the hoses under the sink to take up any slack.
22 OPERATION OPERATION Before Using WARNING • To reduce the risk of fire, electric shock, or injury to persons, read the SAFETY INSTRUCTIONS before operating this appliance. NOTE • Connect to the hot water supply only. The water supply temperature should be a minimum of 120 °F (49 °C) for better washing performance and shorter cycle time.
Page 23
OPERATION three seconds to set the display to automatically turn off a few minutes after the cycle ends. • It is normal for the dishwasher to chime continuously if you open it during operation or just after the cycle ends. The dishwasher is letting you know that the interior temperatures of the unit are hot and to use caution when reaching inside.
24 OPERATION Control Panel Control Panel Features Power On/Off Button • Press this button to turn the washer on or off. • After the cycle is complete, the power automatically turns off for purposes of safety and economy. • If there is a power surge, power outage, or disruption of any kind, power is automatically turned off for safety.
OPERATION • : Wi-Fi - When the appliance is connected to the internet through a home Wi-Fi network, this icon illuminates. - Press and hold Delay Start for approximately three seconds to connect to the network. • : Night Dry - This indicator lights up when Night Dry is selected.
26 OPERATION Half Load NOTE This option washes intensively by selecting the • Only the cycle code for the current Download upper or lower racks. For small loads, use just the Cycle appears on the appliance. See the upper or lower rack to save energy and time. Press smartphone app for cycle codes, names, and the Half Load button repeatedly to select the more information about the available cycles.
Page 27
OPERATION • When the rinse aid is empty, the Extra Dry • The Night Dry option is selected by default for option is selected automatically. all cycles for which it is available, except the Normal cycle. • To add the Night Dry option to the Normal Night Dry cycle, press and hold Extra Dry for 3 seconds.
28 OPERATION NOTE • Options are not available for Download Cycle. Machine Cycle Turbo Express Rinse Clean Soil Level Heavy Light Light 27.5 20.4 12.3 Water Usage (gal) Wash Time with 60 - 34 - Options (Mins.) Dual Zone Half Load Energy Saver High Temp Available...
OPERATION Loading 12 Place Settings • Hand painted silver or gold leaf china • Wood or bone handled utensils 4 6 5 • Iron or non-rustproof utensils • Plastic items which are not dishwasher safe • Sterling silver or gold-plated flatware or delicate or metal-rimmed china •...
Page 30
30 OPERATION Loading 12 Place Settings Case 2 Loading Dishes & Pots Lower Rack Loading Tips: • Plates should be positioned upright and facing the center of the rack, and pots, pans and large dishes must be turned upside down. •...
OPERATION Loading the Upper Rack Loading Dishes into the Upper Rack Loading 10 Place Settings NOTE • The silverware basket ships installed at the back of the bottom rack. For best performance, install it along the right side as shown. Loading 12 Place Settings Upper Rack Loading Tips: •...
Page 32
32 OPERATION necessary to remove the cutlery rack if one is present. (For models with cutlery rack) Loading the Cup Rack Extra cups or cooking utensils can be laid on the fold down cup racks, which also provide support for long-stemmed glasses. Slide the cup rack off the support bar on the opposite side.
Page 33
OPERATION Loading Dishes & Pots on both sides. If the height is not the same on both sides, the dishwasher door will not shut and the upper spray arm will not connect to the water inlet. • There is a 2 3/16 inches (56 mm) gain in height when the upper rack is moved to the lower Height Adjustable Upper Rack position.
34 OPERATION Raising the Rack back to snap the support out of the hooks in the rear. Repeat on the opposite side. Lift the rack at the center of each side until the rack locks into place in the upper position. It is not necessary to lift the lock levers to raise the rack.
OPERATION Adding Cleaning Products CAUTION • Do not place bowls in the center of the cutlery Adding Detergent to the Dispenser rack. The door may not close properly, resulting in leakage. • Remove the label on the dispenser prior to running the dishwasher for the first time.
Page 36
36 OPERATION If a prewash is desired, fill the recessed NOTE prewash compartment area on the lid with detergent. • Using liquid rinse aid improves drying performance by allowing water to drain off of dishes after the final rinse. • Do not use detergent tablets for shorter wash cycles.
Page 37
OPERATION Press Delay Start to change the rinse aid dispenser setting. Each press of the button changes the setting one step from L0 to L4. Once the desired rinse aid dispenser setting is selected, press Start to save. Refilling the Rinse Aid How often the dispenser needs to be refilled depends on how often dishes are washed and the rinse aid setting used.
Internet service provider or refer to your wireless router manual. The notifications are triggered even if the SIGNATURE KITCHEN SUITE application is off. • SIGNATURE KITCHEN SUITE is not responsible for any network connection problems or any faults, malfunctions, or errors caused by network connection.
Page 39
SUITE Application the user’s authority to operate the equipment. Search for the SIGNATURE KITCHEN SUITE application from the Google Play Store or Apple App Store on a smartphone. Follow instructions to FCC RF Radiation Exposure download and install the application.
• Do not press any other buttons. SIGNATURE KITCHEN SUITE will also provide open source code to you on CD-ROM for a charge Place the mouthpiece of your smartphone covering the cost of performing such distribution close to the logo.
Page 41
SMART FUNCTIONS After the data transfer is complete, the diagnosis will be displayed in the application. NOTE • For best results, do not move the smartphone while the tones are being transmitted.
42 MAINTENANCE MAINTENANCE To maintain performance and prevent trouble, it is important to check the outside and inside of the dishwasher, including filters and spray arms, at regular intervals. WARNING • When cleaning the outside and inside of the dishwasher, do not use benzene or thinner. Otherwise, it may cause fire or explosion.
Page 43
MAINTENANCE Cleaning the Air Gap • Clean the filters using non-abrasive materials and warm running water. Turn off the dishwasher. Remove the lower rack and position the bottom spray arm so a wider vee is open to Remove the air gap cover and the plastic cap the front.
Page 44
44 MAINTENANCE If any food residue blocks the spray arm NOTE holes, remove it with a pin or any sharp tool. • Make sure the filter is assembled correctly before starting a cycle. When assembling, rotate the filter firmly until it clicks. CAUTION •...
Page 45
MAINTENANCE After cleaning the upper spray arm, press it up into place. Turn the nut 1/8 turn clockwise to make sure that the nut locks back into place. After assembly, make sure that the spray arms rotate freely. Seasonal Maintenance and Storage •...
SIGNATURE KITCHEN SUITE dishwashers are designed to be used in conjunction with a rinse aid. Using a rinse aid will maximize the amount of water that has already been sheeted away from the dishes before the dry cycle begins.
Page 47
TROUBLESHOOTING The dishwasher does not rely on a heating element for the drying process; instead, it relies on the heat that is retained by the dishes and the tub during the wash and rinse cycles to turn the moisture in the tub into humidity. Warm, moist air in the dishwasher is then pulled into a condensing duct in the door by a fan.
Page 48
• Make sure that the appliance is properly leveled. Water leakage • Turn off the water supply to the dishwasher and call an SIGNATURE KITCHEN SUITE Customer Information Center at 1-855-790-6655 (U.S.A.) or 1-888-289-2802 (Canada). • The dishwasher makes an alert sound for 10 seconds, and runs the drain pump intermittently.
Page 49
TROUBLESHOOTING Problem Possible Cause & Solution Rinse aid level setting mode is selected. • This is not an error code. This code indicates the current rinse aid level. For more information, refer to the Adding Cleaning Products section. Control Lock is activated. •...
Page 50
50 TROUBLESHOOTING Problem Possible Cause & Solution Door does not close Cutlery rack is not properly loaded. completely. (For • Push the door handle to close the door properly until it clicks. models with cutlery rack) Dishwasher chimes if Bumping into or touching the control panel during operation may result in a disabled panel is touched button sound.
Page 51
TROUBLESHOOTING Problem Possible Cause & Solution Food soil remains on Filters are clogged. dishes. • Clean filters. Cloudiness on Combination of excessive detergent and hard water. glassware. • Use less detergent and use a rinse aid to minimize the problem. Black or gray marks Aluminum items rubbing dishes during cycle.
Page 52
52 TROUBLESHOOTING Problem Possible Cause & Solution Trouble connecting The router frequency is not 2.4 GHz. appliance and • Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4 GHz and smartphone to Wi-Fi connect the appliance to the wireless router. To check the router frequency, check with network your Internet service provider or the router manufacturer.
LIMITED WARRANTY TERMS AND CONDITIONS Should your SIGNATURE KITCHEN SUITE Dishwasher (“Product”) fail due to a defect in materials or workmanship under normal and proper use, during the warranty period set forth below, SIGNATURE KITCHEN SUITE will, at its option, repair or replace the Product. This limited warranty is valid only to the original retail purchaser of the Product (“You”) and applies only when purchased lawfully and...
Page 54
The cost of repair or replacement under these excluded circumstances shall be borne by You. TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION Call 1-855-790-6655 and select the appropriate option from the menu. Or visit our website at http://www.signaturekitchensuite.com. Or by mail: SIGNATURE KITCHEN SUITE Customer Service P.O. Box 240007 Huntsville, AL 35813 ATTN: CIC...
Page 55
CANADA TERMS AND CONDITIONS Should your SIGNATURE KITCHEN SUITE Dishwasher ("Product") fail due to a defect in materials or workmanship under normal and proper use, during the warranty period set forth below, SIGNATURE KITCHEN SUITE will, at its option, repair, replace or pro rate the Product upon receipt of proof of the original retail purchase.
Page 56
• Damage or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts of God, or any other causes beyond the control of SIGNATURE KITCHEN SUITE or the manufacturer; • Damage or failure resulting from misuse, abuse, improper installation, repair, or maintenance of the Product.
Page 57
LIMITED WARRANTY Make certain that no dishes or Poor wash results caused by utensils are in the path of the improper loading or over stacking: spray arms. wash arm won't rotate or soap Do not place one dish on top of dispenser is held closed.
Need help?
Do you have a question about the SKSDW2401S and is the answer not in the manual?
Questions and answers