Advertisement
Quick Links
HP Series
HP-100/120
Absolute Air & Gas Ltd
C6 Bromsgrove Technology Park
Email: enquiries@absoluteairandgas.co.uk
www.absoluteairandgas.co.uk
Air pump
Start of production Discontinuance of production
HP-100
1997/10
HP-120
1997/10
STRUCTURE AND PART NAMES
HP-100/120
漓 Filter Cover
滷 Semi Cover Packing
澆 Filter
潺 Fitting Boss
潸 Upper Housing
澁 Sound Absorber (Lap)
澀 Casing Block A
潯 Valve Chamber packing
潛 Casing Block B
濳 Valve
潭
Diaphragm Ring
澂
Diaphragm
潼
Diaphragm Base
潘 Frame Cover
澎 SP Switch
澑 Safety pin+Locking collar
濂 Electromagnet
潦 Actuating Rod
澳 L-Tube
澣 Hose Band
澡 Frame
澤 Vibration Control Rubber
澹 Center Plate
濆 Gasket
澪 Sound Absorber (Filter)
濟 Lower Housing
濕 Power Cord
Isidore Road
Bromsgrove
B60 3FJ
Tel: 01527 557006
─
─
1
Advertisement
Related Manuals for Absolute HP Series
Summary of Contents for Absolute HP Series
- Page 1 HP-100/120 Absolute Air & Gas Ltd C6 Bromsgrove Technology Park Isidore Road Bromsgrove B60 3FJ Tel: 01527 557006 Email: enquiries@absoluteairandgas.co.uk www.absoluteairandgas.co.uk Air pump Start of production Discontinuance of production ─ HP-100 1997/10 ─ HP-120 1997/10 HP Series STRUCTURE AND PART NAMES HP-100/120 漓...
- Page 2 HP- 100 / 120 REPLACING THE CHAMBER BLOCK ！ CAUTION ●Be sure to unplug the pump unit. ●Replace the diaphragms and the valves with new ones at least once a year to one and a half year regularly in order to maintain their initial performance. ●For chamber block replacement, be sure to change both chamber blocks at the same time.
- Page 3 HP- 100 / 120 REPLACING THE CHAMBER BLOCK Remove the 4 screws holding the chamber block and the casing block. (4 screws on each side) Remove 1 U-lock nuts from one side holding the diaphragm mounting block to the rod. ●Use the nut driver to loosen (or tighten) the U-lock nut.
- Page 4 HP- 100 / 120 REPLACING THE CHAMBER BLOCK Fit a new diaphragm and diaphragm ring in the diaphragm base. ●Be sure not to leave a gap between them. REPLACING THE VALVE In case of replacing the whole diaphragm casing block, move straight to STEP 12 Separate casing A and casing B.
- Page 5 HP- 100 / 120 REPLACING THE CHAMBER BLOCK FITTING THE CHAMBER BLOCKS Fit the actuating rod by aligning it with the groove and tighten U-lock nut and flat washer by the nut driver. ●Use new U-lock nut and washer, otherwise, U-lock nut may work loose and cause malfunction.
- Page 6 HP- 100 / 120 REPLACING THE CHAMBER BLOCK Insert a new safety pin through the hole on the terminal side. (Please Insert safety pin through the spring electrode, L-shaped lever in such order.) Install the locking collar from the other side of the terminal and insert it until it clicks.
- Page 7 HP- 100 / 120 REPLACING THE CHAMBER BLOCK Install the sound absorber. Place the upper housing back on body. ●Be extremely careful not to catch the sound absorber on the upper housing. Fasten it with the bolts. Then, place the filter and filter cover on the upper housing.
- Page 8 HP- 100 / 120 REPLACING THE ELECTROMAGNET ！ CAUTION ●Be sure to unplug the pump unit. ●When performing replacement work, the pump body may still be hot and you could get burned. So please wait until the pump has cooled before handling. ●Be sure to remove the chamber block and the actuating rod before replacing the electromagnet.
- Page 9 HP- 100 / 120 REPLACING THE ELECTROMAGNET FITTING THE ELECTROMAGNET Mount new the electromagnets in the unit. Tighten up nuts with nut driver. Install the SP switch to the frame with the screws. ●Be careful of the direction of switch lever. (Refer to the pictures) Insert the wire into the silicon tube, and tie up in a bundle.