Related Manuals for Flexit cvROBO
Summary of Contents for Flexit cvROBO
- Page 1 119740EN-03 2022-03 cvROBO ART.NO. 119721 MANUAL Robot vacuum cleaner with mopping function...
-
Page 2: General Infomation
• Do not leave power cords running charging dock. connected to them that could by • cvROBO must not be used by children dragged by cvROBO or damaged by aged 8 years or younger and by tipping over or falling. -
Page 3: Battery And Charging
• Technical assistance must be carried original spare part. out by authorised personnel. cvROBO does not contain any components that • Only use original batteries for cvROBO can be repaired by the end user. TR800. • The charging dock must only be installed in environments protected against rain or thunderstorms. -
Page 4: Material Provided
R O B O 2. Material provided After opening the packaging, check that the following components – all supplied with cvROBO – are present: cvROBO cvROBO charging dock charging dock charger Accessories tank with water brush cleaning dispenser... -
Page 5: Description Of The Components
Description of the components VIEW FROM ABOVE cvROBO push button panel Side sensor Tank with water dispenser Filter Filter compartment (MOP) Dust container Container opening lever Dust container c v R O B O... -
Page 6: View From Below
Rear wheel with shock absorber Front swivelling wheel Anti-fall sensors Edge-sweeping side brushes Anti-fall sensors Anti-fall sensors Collision guards and sensor cvROBO charging dock Connector for connecting the self- cleaning base VIEW FROM BELOW Charging indicator light Green LED on - power present... -
Page 7: Installation
For optimal results, the temperature of the direct sunlight from domestic environment must be between reaching the charging 10°C and 40°C. dock as it may interfere with the communication and hamper the regular operation of cvROBO. c v R O B O... - Page 8 Position the charging dock at least 100 cm which the robot is inserted touches the away from stairs, empty zones and walls, wall. so that cvROBO can leave the charging dock freely. Make the electrical connection to power the charging dock as shown in the picture.
-
Page 9: Connection Diagram
Installing the charging dock with the docking station In this solution, the docking station is eliminate the dust collected by cvROBO connected to a central vacuum unit to without the user’s direct intervention. 4.1. CONNECTION DIAGRAM protective cover docking station interface... -
Page 10: Charging The Battery
2 hours to charge completely. battery is fully charged. Low battery level blue light on the push-button panel If the battery level is below 20%, cvROBO becomes steady. will not be able to function. In such case, it must be placed manually... - Page 11 (supplied). cleaning, move any objects lying in the • If the cvROBO is cleaning in a working way such as electrical cables, shoes, area larger than 80 square meters (not handbags with straps, magazines and...
- Page 12 R O B O Anti-fall sensors • Anti-fall sensors do not guaranty • cvROBO is equipped with anti-fall that cvROBO stops in the presence sensors to stop it in presence of stairs compulsory to use a magnetic barrier...
-
Page 13: Cleaning Programmes
Place cvROBO manually in the centre of the spot to be cleaned and activate the cleaning cycle by pressing the button for 6 seconds. - Page 14 R O B O 7. cvROBO control modes cvROBO has two control modes: cvROBO push-button panel and cvROBO app Operation with the push-button panel The push-button panel allows for using the following control modes: Function Buttons on cvROBO...
- Page 15 7.1. OPERATION WITH THE CVROBO APP To use the cvROBO app with a smartphone/tablet, it is necessary to access the Internet through a Wi-Fi network. To access the cvROBO app for Android and iOS platforms, scan the adjacent QR code.
-
Page 16: Cleaning Modes
R O B O 8. Cleaning modes cvROBO has two cleaning modes: DUST REMOVAL (STANDARD) - FLOOR WASHING The modes are enabled automatically on the basis of the type of container/tank inserted on cvROBO. 8.1. DUST REMOVAL (STANDARD) edge-sweeping side brushes and the main brush. - Page 17 (S) and the moisture depending on how much water was dispensed by cvROBO. With the cvROBO app and the remote control, it is possible to choose the level of water dispensed to the MOP. Please note!
- Page 18 The supplied barrier is 1 m long. Examples of use With multiple magnetic barriers If cvROBO is located far from the charging dock, it may lose the communication and Multiple magnetic barriers laid in series continue cleaning the same zone without...
-
Page 19: Routine Maintenance
10. Routine maintenance To guarantee optimal performances from cvROBO, complete the single routine maintenance operations listed in this chapter. The maintenance intervals listed in the table are subject to change in relation to the type of domestic environment, the presence of pet animals and how frequently the robot is used. - Page 20 R O B O 10.1. CLEANING THE DUST CONTAINER - (SELF-CLEANING FUNCTION) With docking station The dust container is cleaned automatically when cvROBO returns to the docking station. docking station Periodic inspection of the dust container We recommend periodically checking the dust container manually and clearing it thoroughly from any materials not sucked up by the central vacuum unit.
- Page 21 10.2. CLEANING/REPLACING THE FILTERS Warning! Filters shall not be washed. 1 - Remove the dust container and open removing dirt residues. 1 - Open the dust container, empty it and clean it thoroughly. the two rings on the side (W). dirt residues.
-
Page 22: Cleaning/Replacing The Brushes
R O B O 10.3. CLEANING/REPLACING THE BRUSHES We recommend using the comb (C) supplied with cvROBO. Cleaning the main brush 1 - Open the cover (Q) using the two levers (L). 2 - Extract the main brush (R) from its housing. -
Page 23: Cleaning The Sensors
10.4. CLEANING THE SENSORS Use a damp cloth to clean all the sensors and indicated charging contacts on cvROBO and on the charging dock. Do not use solvents or chemical products. 10.5. CLEANING THE WHEELS Thoroughly clean the wheels by removing hair, threads and residues using the comb supplied. - Page 24 Velcro fasteners (D). 6 - Insert the tank again all the way down until you hear a CLICK. cvROBO will now be ready to wash the Warning! Once the washing cycle terminates, empty the tank of any residual water and wash the micro-fibre cloth.
-
Page 25: Troubleshooting
Action Check for any obstructions and clean the Main brush clogged main brush Main brush worn out Replace the brush cvROBO does not clean Edge-sweeping side brushes Replace the brushes worn out Filters very dirty or damaged Check the water in the tank... - Page 26 Check the power supply connection powered The communication sensor of Clear the sensor from any dust or debris cvROBO does not the charging dock is dirty return to its base cvROBO communication sensor Clear the sensor from any dust or debris...
- Page 27 Filters, brushes, mop and battery are consumables. Before contacting the vendor, check the designation label and note down the Flexit serial number. The designation label is located on the bottom side. Our products are subject to continuous development and we therefore reserve the right to make changes.
- Page 28 Flexit AS, Televeien 15, N-1870 Ørje www.flexit.com...
Need help?
Do you have a question about the cvROBO and is the answer not in the manual?
Questions and answers