High speed rate rf transceiver data module (9 pages)
Summary of Contents for KYL KYL-300L
Page 1
Co.., , , , Ltd Shen hen KYL KYL Communication Communication Equipment Equipment Co KYL-300L KYL-300L Power Power Wireless Wireless KYL-300L KYL-300L Low Low Power Power Wireless Wireless Transceiver Transceiver Data Data Module Module Transceiver Transceiver Data Data Module...
About KYL-300L KYL-300L ..............3 ..............3 About KYL-300L KYL-300L ..............3 ..............3 II. II. II. II. Features Features Features Features of of of of KYL-300L KYL-300L KYL-300L ............3 ............3 KYL-300L ............3 ............3 III. III. Applications Applications Applications of of of of KYL-300L..........
About KYL-300L KYL-300L KYL-300L KYL-300L, the low power wireless transceiver data module is used as the wireless data transceiver in long-ranges, with the small size, weight and power consumption and good stability and reliability. Narrowband low power UHF wireless data transmitters and receivers with channel spacing as low as 25 KHz.
KYL-300L: III: III: Application KYL-300L: KYL-300L the lower power wireless transceiver data module is suitable for: * AMR Automatic Meter Reading * Wireless alarm and security systems * Building automation, security, wireless monitoring and control of room equipment, Access Control System;...
Page 5
The factory default setting is +5V(7.5V-12V will inform when placing the order).By using better ripple factor, KYL-300L transceivers can also share power supply with other equipment. If possible, a voltage-stabilizing chip with 5V voltage is more recommended as the only power supply than Switch power supply. But if only switch power supply available, the jam by switch pulse to the transceivers should be avoided.
Page 6
Before using KYL-300L, the user needs to make simple configuration based on its own needs to determine the channel,interface mode and data format. The user can change or view the module's interface baud rate, channel and address code.
Page 7
Click “open port”, then will open a small window as the following picture, clients will write the parameters in this windows. d. Click “read paras”. “Read correct” show your connection between KYL module and PC is correct. Fax: Fax:...
Page 8
Communication Equipment Equipment Co.., , , , Ltd Shen hen KYL KYL Communication Communication Equipment Equipment Co If you want to change some technical parameter, you need do as follows. e. User can change the parameter such as channel and interface rate and Parity mode according to actual demand through the button of the left window.
Page 9
Shen Shen Shenz z z z hen Communication Communication Equipment Equipment Co.., , , , Ltd Shen hen KYL KYL Communication Communication Equipment Equipment Co Note: Note: data data rate(Air rate(Air Rate) Rate) not be be be be set...
Page 10
From sleep mode to working, it takes the transceiver 1ms after rising edge. To disable the opened sleep function of KYL-300L, the SLP (SLEEP) pin should be definitely connected with 0 or ground.
Page 11
RxD. RxD. Due to a data processing will be made on user’s data by KYL-300L transceiver using FEC (Forward Error Correction) or other correction algorithm, when RxD of a KYL-300L transceiver ‘A’ receives the data, then transmits it, the other one transceiver ‘B’...
Page 12
In theory, when the interface data rate is faster than the RF data rate, KYL-300L transceivers can sent unlimited-long data package, but any long packages more than 120B are not recommended. The length of each package should be between 60~100B.
Networking Application KYL-300L The communication channel of KYL-300L is half duplex, which is most suitable for the communication mode of point to multi-point. Under this mode, one master station must be set, and all of the rest are slave stations. A unique address is given to each station.
KYL-300L can also be used for point-to-point communication with easier operation. For the programming of serial port, all you have to do is to remember that its communication mode is semi duplex while always observing the time sequence of come-and-go for receiving and transmitting.
Need help?
Do you have a question about the KYL-300L and is the answer not in the manual?
Questions and answers